1. Package Contents
2. Physical Introduction
– 1 –
– 2 –
– 3 –
– 4 –
3. Hardware Installation
Hardware Description
2011-E10680-000
Step 1:
(1) Remove the bottom cover.
(2) Connect one end of the Ethernet cable into the LAN (802.3at PoE)
port of the device and the other end to the PoE port on the PoE
Injector.
(3) Connect the power cord with the PoE Injector and plug the other
end into an electrical outlet.
(4) Connect the second Ethernet cable into the LAN port of the PoE
Injector and the other end to the Ethernet port on the computer.
(5) Place the bottom cover back into the device.
WBS-502AC
Quick Guide
Note
If there is any item missing or damaged, please contact the
seller immediately.
IMPORTANT SAFETY PRECAUTIONS:
1.
LIVES MAY BE AT RISK!
Please be aware of the
electrical wires around. Carefully read the section
"OUTDOOR INSTALLATION WARNING"
in the manual
before installation.
2. Users
MUST
complete grounding wired with the device;
otherwise, a sudden lightning could cause fatal damage
to the device.
EMD (Lightning) DAMAGE IS NOT
COVERED UNDER WARRANTY
.
3. Users
MUST
use the “PoE Injector and Power Cord”
shipped in the box with the device. Use of other options
will cause damage to the device.
Thank you for choosing PLANET Outdoor Wireless CPE. Before installing,
please verify the contents inside the package box. The device mentioned
herein is the brief name of the "Outdoor Wireless AP/CPE".
WBS-502AC
Quick Installation Guide
5GHz 900Mbps 802.11ac
Outdoor Wireless CPE
Step 2:
Pole Mounting
(1) Put the rubber into the bracket.
(2) Plug the dynamic stick into the bracket.
(3) Screw the sealing nut and assemble parts, and make sure they are
well tightened.
(4) Put the lock washer on the dynamic stick.
(5) Assemble the mounting parts to the device.
(6) Thread the open end of the mounting ring through the tab on the
bracket.
(7) Lock and tighten the mounting ring to secure the bracket to the
pole to finish the installation.
– 5 –
– 6 –
– 7 –
– 8 –
Step 1:
The Web management allows you to access and manage the
device easily. Launch the Web browser and enter the default IP
address
“http://192.168.1.253”
.
Step 2:
When the login window appears, please enter the User Name
and the Password. The default User Name and Password are
both
“admin”
. Then click the
Login
button to continue.
For security reasons, it is recommended to change the password at the
first login and memorize it.
4. Web Login
1. Click the
“Start”
button located in the lower-left corner of your
computer.
2. Click
“Control Panel”
.
3. Double-click the
“Network and Sharing Center”
icon.
4. Click
“Change Adapter Settings”
.
5. Double-click
“Local Area Connection”
.
6. Select
“Internet Protocol Version 4 (TCP/IPv4)”
and click
“Properties”
.
7. Select
“Use the following IP address”
and then click the
“OK”
button twice to save the configuration. For example, you may choose
from 192.168.1.1 to 192.168.1.254 excluding the default IP address
of the device (192.168.1.253).
A computer with wired Ethernet connection is required for the first-time
configuration of the device.
Further Information:
The above steps introduce the simple installations and configurations of
the device. For further configurations, please refer to the user manual,
which can be downloaded from the website.
WBS-502AC:
http://www.planet.com.tw/en/support/download.php?ty
pe1=4&model=48985&type=3
If you have further questions, please contact the local dealer or
distributor where you purchased this product.
Mounting Ring x 1
Sealing Nut
x 1
Step 3:
Wall Mounting
(1) Put the rubber into the bracket.
(2) Plug the dynamic stick into the bracket.
(3) Screw the sealing nut and assemble parts, and make sure they are
well tightened.
(4) Put the lock washer on the dynamic stick.
(5) Assemble the mounting parts to the device.
(6) Mark and drill two pilot holes aligning to the screw holes of the
bracket.
(7) Put wall anchors into the holes and insert screw into the wall
anchor.
(8) Screw and secure the bracket in place to finish the installation.
Default IP Address:
192.168.1.253
Default User Name:
admin
Default Password:
admin
Default SSID:
PLANET1
Step 3:
After you enter into the Web User Interface, click
Wireless
on
the left hand side of the screen to configure the wireless
connection. Once the basic configuration of the device is done,
go to the
Changes
page to save and apply the changes.
Dynamic Stick x 1
Rubber x 1
Screw Set x 1
Bracket x 1
PWR
WLAN
LAN
Reset Button
LEDs
LAN2 (802.3af PoE Out)
LAN1 (802.3at PoE In)
6
7
1
2
3
4
5
1
2
3
4
5
1
1
4
2
2
3
5
To PC
6
7
8
PoE Injector & Power Cord
