Zoom 4575 User Manual Download | Manualshive

Page: 55 / 56

background image

Appendix C: Compliance

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against radio interference in a residential environment. This
equipment can generate, use and radiate radio frequency energy and, if not installed and
used in accordance with the instructions in this manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is likely to
cause interference, in which case the user, at his own expense, will be required to take
whatever measures are necessary to correct the interference. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference
by one of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

The device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

Output power is conducted. This device is to be used in mobile or fixed applications only.
Antenna gain including cable loss must not exceed 2.5 dBi in the 850 MHz Cellular band
and 2.5 dBi in the PCS 1900 MHz band, for the purpose of satisfying the requirements
of 2.1043 and 2.1091.

FCC Caution:

Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate this equipment.

.

55

«
...
53
54
55
56
»

Summary of Contents for 4575

























































Reviews:

No comments

Related manuals for 4575

Brand: ABB Pages: 6

RM356 - Router - EN

Brand: NETGEAR Pages: 2

Brand: ATO Pages: 18

Brand: Flexitron Pages: 100

Brand: ORANGE Pages: 12

Brand: GE Pages: 5

Brand: Cisco Pages: 20

Brand: Sony Pages: 25

CLIE PEGA-MD700

Brand: Sony Pages: 42

Brand: Sony Pages: 44

Brand: Sony Pages: 86

Brand: Sony Pages: 108

Brand: 3onedata Pages: 3

MultiConnect microCell MTCM2-L4G1

Brand: Multi-Tech Pages: 27

2.4 MIU/PowerPort Series

Brand: Raymar Pages: 30

Brand: Ebyte Pages: 17

Brand: PROLiNK Pages: 16

Brand: PROLiNK Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands