background image

15

RECTANGULAR ZONE DAMPERS

ZONE DAMPERS

Rectangular zone dampers are available for the DigiTract 4 controllers in three (3) styles:
TREC WxH for low pressure applications (5 tons or less) rated at .5” SP;
STMRTD WxH for medium pressure applications up to 7.5 tons, rated at 1” SP;
STCD WxH for heavy duty applications over 7.5 tons, rated at 1.75” SP.

RECTANGULAR LOW PRESSURE ZONE DAMPERS 

(TREC W x H)

Zonex Systems rectangular low pressure dampers can be used for 

systems up to 5 tons with a maximum differential static pressure of 

0.5”. These are two position, spring open, power closed dampers. 

They are constructed from heavy duty galvanized steel. The 

damper is a single blade type that slips into a 2-1/2” wide cutout 

in the existing duct and attaches with screws via a duct mounting 

plate. The duct mounting plate is 5” wide. The drive assembly 

supports a sychronous 24V AC 60Hz 12VA motor and terminal 

board. The motor is designed for continuous full stall operation. 

Special winding and heavy duty gearing provide for long motor 

life and easy spring open operation. A cross pin on the motor 

shaft provides positive direct drive to the damper shaft without a 

coupling or set screws. Motor drive time from full open to full 

close is 30 seconds. A red LED will illuminate on the damper 

terminal board to indicate when the damper is being powered 

closed. The LED will remain on when the damper is fully closed 

and cycle off when the damper is opening or in the full opened 

position. Since this is a spring open damper, in the event of power 

failure the damper fails to the full open position.

RECTANGULAR MEDIUM PRESSURE ZONE DAMPERS 

(STMRTD W x H)

Zonex Systems rectangular medium pressure dampers are recom-

mended for systems under 7.5 tons with maximum differential 

static pressure of 1”. These are power open, power close dampers. 

They are constructed from heavy duty aluminum and stainless 

steel. The dampers is an opposed blade type that slips into a 

3-1/4” wide cutout in the existing duct and attaches with screws via 

a duct mounting plate. The duct mounting plate is 5” wide. Power 

consumption is 2VA. The motors are designed for continuous full 

stall operation. Special winding and heavy duty gearing provide 

for long motor life.

RECTANGULAR HEAVY DUTY ZONE DAMPERS 

(STCD W x H)

Zonex Systems rectangular heavy duty dampers are recommend-

ed for systems 7.5 tons or larger with a maximum differential static 

pressure of 1.75”. These are power open, power close dampers 

made of 20 gauge “snap-lock” steel frame with S and drive duct 

connections. Allow a 16” gap in the duct for the damper. Formed 

steel blade stops incorporate a gasket for quiet operation and 

improved structural rigidity. Rectangular dampers under 10” in 

height incorporate a single blade design. Dampers 10” or over use 

opposed blade design. Power consumption is 2VA. The motors are 

designed for continuous full stall operation. Special winding and 

heavy duty gearing provide for long motor life.

MEDIUM PRESSURE (STMRTD W x H)

HEAVY DUTY (STCD W x H)

LOW PRESSURE (TREC W x H)

Summary of Contents for DigiTract 4





























Reviews: