background image

G U I T A R S

G U I T A R S

25

24

ZB-3

MODELS: Sonus 4, 5, 6, 8 & Special

Description:

Hand-assembled components housed 

in an electrostatically shielded, epoxy module

Function:  

Master volume, pickup blend, bass and tre-

ble boost/cut

Specifications: 

Output level -10dBm

Power requirements: 

One 9-volt battery

Battery life expectancy:

500 hours continuous use

About the system

Master volume control

Controls overall volume level. Turning the con-

trol clockwise increases the volume; turning the control counterclock-

wise decreases the volume.

Pickup blend control. 

Controls relative blend of pickups. Turning the

control clockwise emphasizes the bridge pickup. Turning the control

counterclockwise emphasizes the neck pickup. The detent, or “click,” in

the center of the control is the point where both pickups are on equally.

Bass control. 

15dB. boost or cut of bass at a center frequency of

50Hz. Turning the control clockwise boosts the bass. Turning the control

counterclockwise cuts the bass. The detent, or “click,” in the center of

the control is the “flat” position, zero boost or cut.

Treble control.

15dB boost or cut of treble at a center frequency of

5kHz. Turning the control clockwise boosts the treble. Turning the con-

trol counterclockwise cuts the treble. The detent, or “click,” in the center

of the control is the “flat” position, zero boost or cut.

Trimmer. 

This control on the circuit module attenuates overall output

level. Its factory setting is the mid position.

Caution: 

Setting gain too high may cause distortion.

08

05

9-V

olt Batter

y

Pickup blend

Treble (center)

Trimmer sets maximum gain

Bass (outer ring)

Master volume

Summary of Contents for Hyperbass






















Reviews: