background image

End TIdal Carbon Dioxide (EtCO

2

)

EtCO

2

 - 7

 

2. Check that connections have been made correctly by 

verifying the presence of a proper CO

waveform on 

the M Series display. 

3. The sensor cable should face away from the patient. 

To secure the sensor cable safely out of the way, 
attach Sensor Cable Holding Clips to the airway 
tubing, then connect the sensor cable to the clips.

Applying an Airway Adapter with Mouthpiece

The disposable Pediatric/Adult airway adapter with 
mouthpiece can be used for spot checking CO

on 

non-intubated adult or pediatric patients.   

CAUTION!

The disposable Pediatric/Adult Airway 
Adapter with mouthpiece is intended for 
single patient use. Do NOT reuse or sterilize 
the adapter, as system performance will be 
compromised.

1. Remove adapter with mouthpiece from the package. 

Verify that the adapter and mouthpiece are intact and 
securely fastened to each other.

2. Attach the airway adapter to the CAPNOSTAT 3 

sensor, as follows:

a. Align the arrow on the bottom of the airway adapter 

with the arrow on the bottom of the 
CAPNOSTAT 3.

b. Press the sensor and airway adapter together until 

they click (see Figure 3).

3. If the unit displays the “CHECK CO2 ADAPTER” 

message, follow steps a through c, else go to step 4.

a. Verify proper connection of the adapter to the 

sensor.

b. Verify that the airway adapter windows are clean 

and dry.

c. If the adapter is properly connected, and the 

windows are clean and dry, then zero the adapter 
as described in "Zeroing the Mainstream Sensor/
Airway Adapter" on page 6.

4. Ensure the patient seals his or her mouth completely 

around the mouthpiece and breathes normally.

Note

A nose clip may be needed if the patient is exhaling 
through the nose. It is important that all, or most, of 
the exhalation be routed through the airway 
adapter.

Sidestream EtCO

2

 Setup

There are several steps involved with sidestream EtCO

2

 

setup, as follows:

Selecting a Sidestream Airway Adapter Kit or Cannula 

Attaching the LoFlo Module Cable and Inserting the 
Sample Cell

Zeroing the LoFlo CO2 Module

Applying a Sidestream Airway Adapter Kit 

Applying a Nasal or Nasal/Oral Cannula

Selecting a Sidestream Airway Adapter Kit

Select an airway adapter kit based on the patient's size, 
ET tube diameter, and monitoring situation. Airway 
adapter kits are disposable and single patient use. 

$ISPOSABLE.EONATAL!IRWAY!DAPTER

#!0./34!4#/

3ENSOR

4O0ATIENT 

6ENTILATOR7YE

Figure 2

Airway Adapter Kit

ET Tube Diameter

Adult/Pediatric Airway Adapter Kit

> 4.0 mm

Adult/Pediatric Airway Adapter Kit 
with Nafion® tubing

4O0ATIENT 

#!0./34!4#/

3ENSOR

-OUTHPIECE

!IRWAY!DAPTER

Figure 3

Summary of Contents for Capnostat 3

























Reviews: