background image

2

© Copyright 2020 Zoeller

®

 Co. All rights reserved.

LIMITED WARRANTY

1.  Zoeller Grinder Pumps are designed for grinding and pumping sewage from 

single family residential and commercial duty sewage pump stations.  The 

pump is intended to grind and pump reasonable quantities of items normally 

found in residential sewage.

2.  Zoeller Grinder Pumps can be installed in new applications or as a direct 

replacement for any grinder application of like size and capacity.

3.  Refer to the Zoeller models 810 and 815 when retrofitting  existing positive 

displacement pump installations.

Applications

Contact Manufacturer at, 3649 Cane Run Road, Louisville, Kentucky  40211, Attention: 

Customer Support Department to obtain any needed repair or replacement of 

part(s) or additional information pertaining to our warranty.

MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL, 

CONSEQUENTIAL OR INCIDENTAL DAMAGES OR BREACH OF EXPRESSED 

OR IMPLIED WARRANTY; AND ANY IMPLIED WARRANTY OF FITNESS FOR A 

PARTICULAR PURPOSE AND OF MERCHANTABILITY SHALL BE LIMITED TO THE 

DURATION OF THE EXPRESSED WARRANTY.

Some states do not allow limitations on the duration of an implied warranty, so 

the above limitation may not apply to you. Some states do not allow the exclusion 

or limitation of incidental or consequential damages, so the above limitation or 

exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other rights 

which vary from state to state.

Manufacturer warrants, to the purchaser and subsequent owner during the 

warranty  period,  every  new  product  to  be  free  from  defects  in  material  and 

workmanship under normal use and service, when properly used and maintained, 

for a period of three years from the date of purchase. Proof of purchase is required. 

Parts that fail within the warranty period, that inspections determine to be defective 

in material or workmanship, will be repaired, replaced or remanufactured at 

Manufacturer's option, provided however, that by so doing we will not be obligated 

to replace an entire assembly, the entire mechanism or the complete unit. No 

allowance will be made for shipping charges, damages, labor or other charges 

that may occur due to product failure, repair or replacement.

This warranty does not apply to and there shall be no warranty for any material 

or product that has been disassembled without prior approval of Manufacturer, 

subjected to misuse, misapplication, neglect, alteration, accident or act of 

nature; that has not been installed, operated or maintained in accordance with 

Manufacturer's  installation  instructions;  that  has  been  exposed  to  outside 

substances including but not limited to the following:  sand, gravel, cement, mud, 

tar, hydrocarbons, hydrocarbon derivatives (oil, gasoline, solvents, etc.), or other 

abrasive or corrosive substances, wash towels or feminine sanitary products, etc. 

in all applications other than raw sewage pumping applications.  The warranty 

set out in the paragraph above is in lieu of all other warranties expressed or 

implied; and we do not authorize any representative or other person to assume 

for us any other liability in connection with our products.

*Zoeller Company does not recommend a simplex station on anything over two homes in order to maintain continuous service during unusual  conditions.

Recommended Limits of Application 800 Series Grinder Pumps

These recommended application limits are for pump stations pumping to a gravity main.  Low-pressure pipe systems should be designed with a pump located at 

each house.  For applications where a lift station would handle between 15 and 60 homes, consider the 71 Series grinder pump.  For applications where a lift station 

would handle more than 60 homes, a solids handling type pump should be considered.

Simplex Station

Duplex Station

Model

HP

Homes

GPD

Homes

GPD

810 Progressing Cavity Grinder

1.0

1

400

2

800

815 Progressing Cavity Grinder

2.0

1

400

2

800

818

1.0

1

400

2

800

819

1.5

1

400

2

800

820

2.0

1

400

2

800

840 w/o Reversing Control

2.0

2*

800

10

4,000

840 w/ Reversing Control

2.0

2*

800

15

6,000

841

2.0

2*

800

10

4,000

842

2.0

2*

800

10

4,000

In instances where property damages are incurred as a result of an alleged product failure, 

the property owner must retain possession of the product for investigation purpose.  

Summary of Contents for SHARK 800 Series













Reviews: