background image

© Copyright 2019 Zoeller

® 

Co. All rights reserved.

8

OUTLINE / DIMENSIONAL SIZE

IL1212

6.02

13.96

6.22

6.89

6.3

7.28

5.71

5.12

8.98

8.62

NPT1"

NPT1"

Outlet

Inlet

4.13

1.77

4- 0.4

8.07

NPT1"

6.3

7.28

5.12

NPT1"

6.35

16.11

6.55

6.89

8.62

5.71

8.98

4.13

1.77

Outlet

Inlet

4- 0.4

8.07

350

355

in lieu of all other warranties expressed or implied; and we do not authorize any 
representative or other person to assume for us any other liability in connection 
with our products.

Contact Manufacturer at, 3649 Cane Run Road, Louisville, Kentucky  40211, 

Attention: 

Customer Support Department to obtain any needed repair or replacement of 
part(s) or additional information pertaining to our warranty.

MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL, 
CONSEQUENTIAL OR INCIDENTAL DAMAGES OR BREACH OF EXPRESSED 
OR IMPLIED WARRANTY; AND ANY IMPLIED WARRANTY OF FITNESS FOR A 
PARTICULAR PURPOSE AND OF MERCHANTABILITY SHALL BE LIMITED TO THE 
DURATION OF THE EXPRESSED WARRANTY.

Some states do not allow limitations on the duration of an implied warranty, so 
the above limitation may not apply to you. Some states do not allow the exclusion 
or limitation of incidental or consequential damages, so the above limitation or 
exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other rights 

which vary from state to state.

LIMITED WARRANTY

Manufacturer warrants, to the purchaser and subsequent owner during the warranty 
period, every new product to be free from defects in material and workmanship 
under normal use and service, when properly used and maintained, for a period 
of one year from date of purchase. Proof of purchase is required.   Parts that fail 
within the warranty period that inspections determine to be defective in material 
or workmanship will be repaired, replaced or remanufactured at Manufacturer's 
option, provided however, that by so doing we will not be obligated to replace an 
entire assembly, the entire mechanism or the complete unit.  No allowance will 
be made for shipping charges, damages, labor or other charges that may occur 
due to product failure, repair or replacement.
This warranty does not apply to and there shall be no warranty for any material 
or product that has been disassembled without prior approval of Manufacturer, 
subjected to misuse, misapplication, neglect, alteration, accident or uncontrollable 
act of nature; that has not been installed, operated or maintained in accordance 
with Manufacturer's installation instructions; that has been exposed to outside 
substances including but not limited to the following:  sand, gravel, cement, mud, 
tar, hydrocarbons, hydrocarbon derivatives (oil, gasoline, solvents, etc.), or other 
abrasive or corrosive substances, wash towels or feminine sanitary products, 
etc. in all pumping applications.  The warranty set out in the paragraph above is 

In instances where property damages are incurred as a result of an alleged product failure, the property 

owner must retain possession of the product for investigation purpose.  

Summary of Contents for 350









Reviews: