background image

© Copyright 2019 Zoeller

® 

Co. All rights reserved.

4

 

 

Indoor/outdoor area –

 ensure draining through pressure relief 

valve is available in order to avoid damage in case of leakage.  

Outdoor area –

 unit should be covered by a weather proof housing, 

ensure adequate ventilation.

FREEZING (OR REMOVING PUMP FOR MAINTENANCE)

 

 The pump and all piping must be protected 

from freezing. If freezing weather is forecast, and the unit will be 

exposed to temperatures less than 32 ºF (0 ºC), remove the pump by 

closing off ball valves #1 and #2, (see FIG 1) and removing the pump 

using the union connections. Store pump in a heated area. Open 

ball valve #3 to allow city water to pass forward if desired. Ensure 

the piping is adequately protected from the cold environment.

OPERATING CONDITIONS

Ambient temperature range 32 ºF (0 ºC) to 104 ºF (40 ºC).

PRIMING

After installation (with the pump OFF), open ball valves #1 and #2, 

and slowly unthread the air relief plug (FIG 4). Allow inlet water 

pressure  to  fill  the  pump  cavity  and  remove  in-line  air  pockets.  

After the pump cavity fills with water, retighten the air relief plug. 

FIG 4 PRIMING ILLUSTRATION

a. Open ball valves #1 and #2, close 3.

d. Tighten the air 

     relief plug.

c. Ensure water fills

    chamber from city water. 

    Replace plug immediately 

    to avoid excess moisture 

    on pump.

IL1207

b. Loosen the air relief plug.

#1

#2

#3

Torque : 22 in-lb

22

 in-lb

Suction

22

 in-lb

 

 If unit is shut down for an extended period of 

time or air enters into the system, it may be necessary to repeat 

the above priming instructions to ensure the internal pump cavity 

is running with water to avoid dry running damage to the internal 

seals.

Summary of Contents for 350









Reviews: