background image

1

© Copyright 2017 Zoeller

®

 Co. All rights reserved.

DRAIN PUMP SYSTEM 

MODEL 105 (Korean)

 

INSTALLATION INSTRUCTIONS 

PREINSTALLATION CHECKLIST

 

FM3034_Ea

0717

Supersedes

New

Notice to Installer:  Instructions must remain with installation.

MODEL:_______________________

DATE CODE:  __________________

DATE INSTALLED:   _____________

1.   

Inspect your unit.

 Occasionally, products are damaged during shipment. If the unit is damaged, contact  your dealer before using.  DO NOT remove the test 

plugs from the pump. 

2.   

Carefully read the literature

 provided to familiarize yourself with specific details regarding installation and use. These materials should be retained for future 

reference. 

1.  To reduce the risk of electrical shock, a properly grounded receptacle of 

grounding type must be installed and protected by a ground fault circuit 

interrupter (GFCI) and in accordance with National Electrical Code and local 

codes. 

2.  Make certain that the receptacle is within the reach of the pump’s power 

supply cord. DO NOT USE AN EXTENSION CORD.  Extension cords that 

are too long or too light do not deliver sufficient voltage to the pump motor 

and could present a safety hazard if the insulation were to become damaged 

or the connection end were to fall into the sump.

3. 

Testing for Ground.

 As a safety measure, each electrical outlet should be 

checked for ground using an Underwriters Laboratory Listed circuit analyzer 

which will indicate if the power, neutral and ground wires are correctly con-

nected to your outlet. If they are not, call a qualified electrician.

4.  For Added Safety. Pump must be connected to a 3-prong grounded outlet 

interrupter device (ground fault circuit interrupter).

5.  FOR YOUR PROTECTION, ALWAYS DISCONNECT PUMP FROM ITS 

POWER SOURCE BEFORE HANDLING.  Single phase pumps are supplied 

with a 3-prong grounded plug to help protect you against the possibility of 

electrical shock.  DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE 

GROUND PIN.  To reduce the risk of electrical shock, a properly grounded 

receptacle of grounding type  must be installed and protected by a ground 

fault circuit interrupter (GFCI) in accordance with national electrical code and 

local codes.

6.  Installation and checking of electrical circuits and hardware should only be 

performed by a qualified, licensed electrician. 

7.  Risk of electric shock - These pumps have not been investigated for use in 

swimming pool areas.

1.  Check to be sure your power source is adequate for handling the voltage 

requirements of the motor, as indicated on the pump or basin plate. 

2.  Make sure the pump electrical supply circuit is equipped with fuses or circuit 

breakers of proper capacity. A separate branch circuit is recommended, sized 

according to the National Electrical Code and local codes for the current 

shown on the pump name plate. 

3.  All plumbing (discharge and vent lines) must be installed to meet local codes. 

Unit must be vented. DO NOT USE AN AUTOMATIC PLUMBING VENT 

DEVICE SIMILAR TO A "PRO-VENT". Some states require this product to 

be installed by a licensed plumber.

4.  Repair and service should be performed by Zoeller Pump Company Authorized 

Service Station only.

5.  CHECK VALVE MUST BE USED TO REDUCE UNNECESSARY CYCLING 

OF PUMP. 

6.  Dewatering pumps are not designed or intended for handling raw sewage. 

7.  Maximum operating temperature for 105 Drain Pumps must not exceed  

54 °C (130 °F).

8.  For health reasons, do not unplug, turn off, or disable pump and use pump 

tank system as a way to fill up a sink or laundry tray, etc.

9.  Unit is designed for above ground installation only.

SEE BELOW FOR LIST OF WARNINGS

CAUTION

SEE BELOW FOR LIST OF CAUTIONS

REFER TO WARRANTY ON PAGE 2.

Notice to Installer:  Instructions must remain with installation.

Product information presented 

here reflects conditions at time 

of  publication. Consult factory 

regarding discrepancies or 

inconsistencies.

MAIL TO:

  P.O. BOX 16347 • Louisville, KY  40256-0347

SHIP TO:

  3649 Cane Run Road  • Louisville, KY  40211-1961

TEL:

 (502) 778-2731 • 1 (800) 928-PUMP • 

FAX:

 (502) 774-3624

Visit our web site:

www.zoellerpumps.com

Your Peace of Mind is Our Top Priority

 

®

60 Hz

P/N 154927 

Summary of Contents for 105









Reviews: