background image

H0493700.A - EN - 2014-07

1

• 

Read this notice carefully before installing, maintaining or repairing this appliance!

• 

The 

 symbol  indicates important information that must be taken into consideration in order to 

avoid risk of harm to persons or damage to the appliance.

• 

The 

 symbol  indicates useful information.

  

 

 Warnings

• 

As part of a continuous improvement process our products may be modified without prior notice. 

• 

Exclusive use: regulation system for pools (must not be used for any other purpose).

• 

System designed to work with water from the public network. The use of water from wells or rain 

water is prohibited.

• 

The installer is liable for the installation of the appliance and the compliance with local regulations 

in matters of installation. Under no circumstances can the manufacturer be held liable in the event of 

failure to comply with applicable local standards. Under no circumstances shall the manufacturer be 

held liable if current local installation regulations are not followed.

• 

It is important that this equipment is operated by competent and qualified (both physically and 

mentally) people  that  have  previously received  the  instructions  for  use  (by  reading  this booklet). 

Any person not meeting these criteria should not go near the equipment, to avoid the risk of being 

exposed to dangerous components.

• 

If the equipment malfunctions: do not attempt to repair the equipment yourself – contact your 

installer.

• 

Before  working  on  the  equipment,  ensure  that  it  and  any  other  equipment  connected  to  it  are 

disconnected from the electricity supply.

• 

Before  connecting  it  to  the  electricity  supply,  check  that  the  voltage  marked  on  the  equipment 

matches the mains supply voltage.

• 

Removing or bypassing one of the safety devices automatically voids the guarantee, as does fitting 

replacement parts not manufactured by us.

• 

Incorrect installation can result in damaged equipment or serious physical injury (or even death).

• 

Keep the equipment out of the reach of children.

• 

The pH Link or Dual Link module is only designed to use pH minus (special liquid for use in swimming 

pools). Use of other products automatically voids the guarantee.

Summary of Contents for W197515















Reviews: