background image

2

WARNINGS ASSOCIATED WITH ELECTRICAL APPLIANCES

• 

The  power  supply  to  the  appliance  must  be  protected  by  a  dedicated  30  mA 

residual current device, complying with the standards and regulations in force in 

the country in which it is installed.

• 

Do  not  use  any  extension  lead  when  connecting  the  appliance;  connect  the 

appliance directly to a suitable power supply.

• 

Before carrying out any operations, check that:

 -

The  voltage  indicated  on  the  appliance  information  plate  corresponds  to  the 

mains voltage. 

 -

The power grid must be adapted to the power requirements of the appliance, and 

is grounded. 

 -

The plug (where applicable) is suitable for the socket.

• 

In the event of abnormal operation or the release of odours from the appliance, 

turn it off immediately, unplug it from its power supply and contact a professional.

• Before servicing or performing maintenance on the appliance, check that it is 

powered off and completely disconnected from the power supply.

• Do not disconnect and reconnect the appliance to the power supply when in 

operation.

• Do not pull on the power cord to disconnect it from the power supply.

• 

If  the  power  cord  is  damaged,  it  must  be  replaced  by  the  manufacturer,  an 

authorised representative or a repair facility only

.

• 

Do not perform maintenance or servicing operations on the appliance with wet 

hands or if the appliance is wet.

• 

Before connecting the appliance to the power supply, check that the connection 

unit or socket to which the appliance will be connected is in good condition and 

shows no signs of damage or rust.

• 

For  any  component  or  sub-assembly  containing  a  battery:  do  not  recharge  or 

dismantle the battery, or throw it into a fire. Do not expose it to high temperatures 

or direct sunlight.

• 

In  stormy  weather,  unplug  the  appliance  to  prevent  it  from  suffering  lightning 

damage.

• 

Do not immerse the appliance in water (with the exception of cleaners) or mud.

Recycling

This symbol means that your appliance must not be thrown into a normal bin. It will be 

selectively collected for the purpose of reuse, recycling or transformation. If it contains any 

substances that may be harmful to the environment, these will be eliminated or neutralised.

Contact your retailer for recycling information.

Summary of Contents for PSA Red Line 12














Reviews: