background image

 2 

1. GENERAL 

 

1.1 General terms of delivery 

 

Any equipment, even CARRIAGE and PACKING FREE, travel at the consignee’s risk. The consignee shall make 
reserves in writing on the CARRIER’S delivery bill if he notes damage caused during transport. (Confirmation to be sent 
to the CARRIER within 48 hours by registered mail with acknowledgement of receipt). 

 

Reminder:

 

The unit must be shipped and stored in the upright position on a pallet and in the original packaging

. In the contrary 

case, place the unit in the vertical position on the pallet and check its global state (in case of doubt regarding the unit’s good state of 
operation establish reserves in writing with the carrier). 

 

-

 

Under no circumstances may the heat pump be operated immediately if it was placed horizontally. 

Wait at least 12 hours before operating the pump -

 

 

1.2 Voltage 

 

Prior to any operation, check that the voltage on the name plate of the appliance corresponds to the mains voltage 
provided on site. 

 

1.3 Water treatment 

 

In order to use our appliances under the best conditions, the following parameters must be respected: free chlorine: max. 
2.5 mg/l, total bromine: max. 5.5 mg/l, pH between 6.9 and 8.0. If chemical or electrophysical disinfection systems are 
used, the installer and user must contact the supplier to ensure they are compatible with our materials. These systems must 
be installed after the heating system. 

 

2. DESCRIPTION 

 

2.1 Presentation 

 

Contents after unpacking

:   

 

The unit with its instructions, warranty card  

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

Note:

 inside the appliance you will find a sachet of accessories. To extract it, see paragraph 4.1 of these instructions.

 

 
 
 
 
 
                                                                                                                                                                                                                     

 

 

 

Content of sachet: 

two half-union connectors Ø50 with strap   + two sealing rings   - four silent blocks   

 a grooved elbow union  .- a plastic cap 

- four anchor bolts and dowels 

(only supplied with double fan unit

).

 

 

 

 

Must

 be installed 

with a double fan 

machine 

Summary of Contents for Edenpac 2





















Reviews: