background image

2

Recycling

This symbol means that your appliance must not be thrown into a normal bin. It will be selectively collected 

for the purpose of reuse, recycling or transformation. Any substances it may contain which are potentially 

dangerous to the environment shall be eliminated or neutralised.

Request information on recycling procedures from your retailer.

WARNINGS ASSOCIATED WITH ELECTRICAL APPLIANCES

• 

The electrical supply to the appliance must be protected by a dedicated 30 

mA differential residual current protection device (RCD), complying with the 

standards and regulations in force in the country where it is installed.

• 

Do not use an extension cord to plug in the appliance; connect the appliance 

directly to a suitable power supply circuit.

• 

Before carrying out any operations, check that:

- The voltage indicated on the rating plate of the appliance corresponds to the 

mains voltage, 

- The power grid is adapted to the power requirements of the appliance, and is 

grounded. 

- The plug (where applicable) is suitable for the socket.

• 

In the event of abnormal function or signs of overheating such as a burning 

odour from the appliance, turn it of immediately, unplug / disconnect it from 

its power supply and contact a professional.

• 

Before accessing the enclosure for any reason, ensure that all power to the 

appliance and also power to any accessories or external devices which may 

be connected to the appliance, is disconnected from the mains power supply.

• 

Do not disconnect and reconnect the appliance to the power supply when in 

operation.

• 

Do not pull on the power cord to disconnect it from the power supply.

• 

If the supply cord is damaged, it must be replaced by the manufacturer, its 

service agent or similarly qualified persons in order to avoid a hazard.

• 

Do not attempt to carry out any servicing or maintenance operations with 

wet hands or while the appliance is wet.

• 

Ensure that all terminals for mains power are free in good condition and free 

of corrosion and/or dirt/debris.

• 

For any component or sub-assembly containing a battery: do not recharge or 

dismantle the battery, or throw it into a fire. Do not expose it to high tempera

-

tures or direct sunlight.

• 

In stormy weather, disconnect the appliance from the power supply to pre

-

vent it from suffering lightning damage.

• 

Do not immerse the appliance in water (with the exception of cleaners) or 

mud.

Summary of Contents for Chlor Perfect






















Reviews: