background image

12 

1.4 Commissioning 

1.4.1 Different command panel set ups  

 

CAE without options or with heating option  

 

CAE with heating and condenser option

 

  

 

1.4.2 Starting the appliance 

 

 Power on the appliance (by switching on the general terminal board), 

 Only for three-phased CAE: when the dehumidifier is switched on, check the status of the phase 

controller (

KA4

). If it is off, cut off the power supply and invert two phases 

directly

 on the appliance 

connection terminal board. 

 

 

This operation must be only be carried out by a qualified professional. 

 

 

 

 

 

 Activate the switches depending on needs and options(s):  

Trigger(s) / switches 

IG 

ID 

ICE/ICB 

ICC 

Dehumidifier X 

 

 

Dehumi air heating* 

 

Dehumi water condenser 

 

Dehumi air heating* + water condenser 

*extra heating or hot water battery option  

 

 To start up a CAE with options see also §1.4.5. 

 Set the humidity and temperature on the Hygro Control so that it triggers dehumidifying and / or air 

heating (optional), see §1.3.7.4). 

 

The phase order controller protects the compressor. 

It’s 

forbidden 

to

 

invert phases: 

 

-  on the power contactor (KM1 and/or KM2) 
-  on the compressor  
-  on the ventilator 
-  on the thermal protection 
-  on the phase order controller 

If the indicator remains switched off after this operation check for the presence of the 
three phases on the phase order controller KA4. 

Main switch 

Dehumidification switch 

Heater switch

Ventilation (green) 

Dehumidification (green) 

heating (green) 

Fault (red)

Main switch (orange)

Main switch 

Dehumidifier switch 

Heater switch 

Fault (red) 

heating (green) 

Ventilation (green) 

Dehumidifier (green) 

Main switch (orange) 

Water condenser switch

Water condenser (green) 

EN 

Summary of Contents for CAE





























Reviews: