background image

 

 

 
TS3000: 

  Tripod Turnstile 

TS3011:

  Tripod Turnstile with Controller and RFID Reader 

TS3022: 

  Tripod Turnstile with Controller and Fingerprint Reader with RFID function. 

Please read this document carefully before installation and using the device. 

1.

 

Technical Specifications 

Input Voltage 

AC 100V ~ 120V / 200 

~240V,   

50Hz/60Hz 

Max. Tolerance of 

Arms 

Center: 80 kg 

End: 40 kg 

Operating 

Environment 

Indoor and Outdoor 

(shelter) 

Arm Length (mm) 

520 

Operating 

Temperature 

-28ºC ~ 60ºC 

Net Weight 

38kg 

Operating Humidity 

5% ~ 85% 

Gross Weight 

43kg 

Flow Rate 

20 ~ 30 passages / minute 

Dimension(mm) 

Figure 1 

L = 940, W = 260, H = 980 

Input Control Signal 

Dry contact 

Package Size (mm) 

L = 1000, W = 340, H = 

1050 

 

Figure 1-1

 

 

2. Arm Installation and Equipment Testing 

2.1 Arm installation method

 

Installation procedure 

1.

 

Using the glue and applying in the hole of the arms as 
well as the one screw, as shown in Figure 2-1. (This is to 
prevent screws from getting loose due to vibration after 
being used for a long time.) 

 
 

 

 

 

 

 

 
 

Figure 2-1 

This hole shall be 

applied with glue 

evenly. 

Summary of Contents for TS3000 Series













Reviews:

Related manuals for TS3000 Series