Zip Miniboil BA Installation Instructions & User Manual Download Page 9

9

805757 v1.05 06.21 Miniboil Install Instructions

Operation

Note: If the appliance has not been used for several days, allow the tap to 
run ambient water for about one minute.

Tap Operation

Press the RED lever and the SAFETY button to dispense boiling water.
Pull the RED lever up while holding the SAFETY button to dispense boiling water 
continually. The water will flow for about 15 seconds. Then manually return the 
lever to the off position.
Press the BLUE lever to dispense cold (ambient) water. Pull the lever up to 
dispense ambient water continually. The water will flow for about 15 seconds. 
Then manually return the lever to the off position.

Tap Lights

Red LED: Boiling water

•  Steady light: boiling water is ready and can be dispensed.
•  Flashing: the water temperature is below the set value. Boiling water 

cannot be dispensed.

•  Flashing slowly: the unit is in Sleep mode.

Blue LED: Cold (ambient) water (for BA model only)

•  Steady light: ambient-temperature water can be dispensed.

All LEDs: Fault

•  Flashing: there is a fault in the unit. In that case, switch off the unit for 

at least 20 seconds. If the fault has not been corrected when the unit is 
switched on again, contact customer service.

Change Filter light

•  Off: Indicates the water filter is operating within its normal specified 

lifespan.                                                                                                  

•  Flashing slowly: Indicates the water filter is due for replacement, after 12 

months of use or after dispensing 4000 litres, whichever occurs first. To 
replace the filter, refer to Fig 3. After the filter is changed, it should be 
flushed. Refer to Filter flush on previous page.

•  Reset filter counters: After filter is changed, hold down BOTH LEVERS for 

10 seconds. The Filter Change light will turn ON, and after 10 seconds will 
turn OFF. This will reset the filter counters to zero.

Boiling water (BA model):

Press or pull the red lever, 
and cover the Safety button 
at the same time.

Boiling water will be 
dispensed.

Change Filter light

Boiling Only model:

Press or pull either red 
lever, and cover the Safety 
button at the same time.

Boiling water will be 
dispensed.

Cold (ambient) water  
(BA model):

Press or pull the blue lever.

Cold water will be 
dispensed.

Summary of Contents for Miniboil BA













Reviews: