Zimmer MIS Multi-Reference Surgical Technique Download Page 40 | Manualshive

Page: 40 / 48

Zimmer MIS Multi-Reference Surgical Technique Download Page 40

Zimmer MIS Multi-Reference 4-in-1 Femoral Instrumentation Surgical Technique

38

Component Implantation

After the implants have been chosen,
make one last check to ensure that the
femoral, tibial, and articular surface
components match.

Articular Surface

Insertion

The Articular Surface Inserter applies
both downward and rearward forces
to aid in the insertion of the articular
surface onto the tibial base plate.
Push the lever on the inserter fully to
either side. Place the articular surface
onto the tibial base plate, engaging
the dovetails (Fig. 10b). Steady the
surface on the base plate with one
hand by applying downward pressure
near the posterior cruciate cutout.
Engage the hook on the inserter with
the mating slot in the front of the
base plate and close the lever with

your index finger. This should lock the
inserter to the base plate. Squeeze
the handles of the inserter to seat the
articular surface (Fig. 10c). Open the
lever and remove the inserter.

Insert

an articular surface only once. Never
reinsert the same articular surface
onto a tibial base plate.

Fig. 10b

Fig. 10c

«
...
38
39
40
41
42
...
»

Summary of Contents for MIS Multi-Reference

















































Reviews:

No comments