manualshive.com logo in svg

Zimmer MIS Multi-Reference, Surgical Technique, Page: 39 / 48

Share
Download
Zimmer MIS Multi-Reference Surgical Technique Download Page 39

Zimmer MIS Multi-Reference 4-in-1 Femoral Instrumentation Surgical Technique

37

Step Ten

Implant Components

In this step, the final components are 
implanted, and the tibial articular 
surface is secured to the implanted 
tibial base plate. When using cemented 
components, it is recommended to use 
two batches of cement.

After the implants have been chosen, 
make a final check to ensure that the 
femoral, tibial base plate, and tibial 
articular surface components match. 
If using a cemented component, mix 
the first batch of cement. The cement 
should have a doughy consistency 
when ready for use.

Tibial Base Plate

If a stemmed tibial base plate will be 
used with a stem extension, attach the 
desired stem extension to the stem and 
strike it once with a mallet. If a 10mm-
14mm thick tibial articular surface will 
be used, insert the locking screw for 
the stem extension.

If a stemmed tibial base plate will 
be used without a stem extension, 
consider the need for a taper plug. If a 
17mm or 20mm articular surface will 
be used, a stem extension or taper 
plug is required. A taper plug also can 
be used with the 10mm-14mm tibial 
articular surface. If it is planned to 
use a 14mm articular surface or if the 
flexion and extension gaps are not 
balanced, consider using the taper plug 
in case the final reduction reveals that 
it is necessary to switch to a 17mm or 
20mm articular surface. Furthermore, 
if the articular surface should ever 
require revision with a 17mm or 20mm 
thick component, the taper plug is 
already in place and revision of the 
tibial base plate may not be necessary. 
Assemble the taper plug onto the tibial 
plate by striking it several times with a 
mallet to allow the ring on the taper to 
deform.

Position the PCL Retractor posteriorly, 
the Collateral Soft Tissue Protector 
laterally, and the Collateral Retractor 
medially. Sublux the tibia anteriorly. 
Place a layer of cement on the 
underside of the tibial base plate, 
around the keel, on the resected tibial 
surface and in the tibial IM canal. 
Position the tibial base plate onto the 
tibia and use the Tibial Impactor to 
impact it until fully seated (Fig. 10a). 
Thoroughly remove any excess cement 
in a consistent manner.

Femoral Component

Attach the femoral component to the 
Femoral Impactor/Extractor.

Knee in 70°-90° flexion

Place the Collateral Retractor laterally, 
an Army-Navy retractor anteriorly, and  
a rake retractor on the meniscal  
bed medially.

Place a layer of cement on the 
underside of the prosthesis and in the 
holes drilled in the femur.

Attach the Femoral/Impactor/Extractor 
to the femoral component. Insert the 
femoral component onto the distal 
femur by translating the component 
laterally until the lateral peg aligns 
with the drill hole in the lateral femoral 
condyle. Take care to avoid scratching 
the implant component surfaces. 
Disposable, plastic Tibial Plate 
Protectors may be temporarily inserted 
onto the Tibial Base Plate to protect 
the implant surfaces during insertion 
of the femoral component. Remove the 
Tibial Plate Protector after the femur is 
seated. Be sure that soft tissue is not 
trapped beneath the implant. Use a 
mallet to impact the component until 
fully seated.

Remove the Femoral Impactor/
Extractor, and the retractors. Check 
the medial and lateral sides to make 
sure the femoral component is fully 
impacted. Remove any excess cement 
in a thorough and consistent manner.

Alternatively, push the component in 
place by hand beginning laterally, then 
medially.

Fig. 10a Use the Tibial Impactor to impact 

the tibial base plate.

Summary of Contents for MIS Multi-Reference

















































Reviews:

No comments