ZIEHL-ABEGG FXET4AMQ Operating Instructions Manual Download Page 56

Page: 56 / 87

9.10.2.13

“

Freeze function

”

= maintain momentary modulation value, Function

14D

The device continues to work so long independently of the control function with the momentary value
of the modulation and/or speed as activated over the digital input.

Freeze

Message indicated alternating with the active value

“

Freeze Function

”

Contact at digital input e.g.

“

Digital In 1

”

“

D1 Inverting

”

“

OFF

”

“

Freeze function

”

at closed contact activ

“

D1 Inverting

”

“

”

“

Freeze function

”

at opened contact activ

9.10.3

Con

ﬁ

guration of analog inputs

“

”

and

“

”

9.10.3.1

Signal adaption E1 and E2

If required, an adaptation of the speci

ﬁ

cation signal / speed characteristic curve is possible

Information

These settings are mostly practical for the operating mode with rotational speed speci

ﬁ

cation over an

external signal. In operating modes (as of 2.01) this setting is not suited for in

ﬂ

uencing the regulation

process.

E1 Modus

= E1 min. / E1 max. without function (factory setting)

= Offset / turn

= signal range

= for activating the touch function see speed controller programming (function

available depending on the software version)

E1 Min.

Setting range: 0 - 100 %
Factory setting: 0 %

E1 max

Setting range: 0 - 100 %
Factory setting: 100 %

E2 Mode

= E2 min. / E2 max. without function (factory setting)

= Offset / turn

= signal range

= for activating the touch function see speed controller programming (function

available depending on the software version)

E1 Min.

E2 min.

Setting range: 0 - 100 %
Factory setting: 0 %

E1 max

E2 max.

Setting range: 0 - 100 %
Factory setting: 100 %

Operating Instructions

Fcontrol

–

model series FXET4/6/10AMQ

Programming

L-BAL-E079-GB 1706 Index 008

Part.-No.

56/87

Summary of Contents for FXET4AMQ
























































































Search results

Summary of Contents for FXET4AMQ

Reviews:

Brands by name

Popular brands

ZIEHL-ABEGG FXET4AMQ, Operating Instructions Manual

Search results

Summary of Contents for FXET4AMQ

Reviews:

Brands by name

Popular brands