manualshive.com logo in svg

ZIEHL-ABEGG FXET10AMQ, Operating Instructions Manual

Share
Download
ZIEHL-ABEGG FXET10AMQ Operating Instructions Manual Download Page 14

5.2

Terminal compartment

Position of terminals

1

Line

2

Motor

3

Indication relays

4

Modulation

5

MODBUS

5.3

EMC-compatible installation

5.3.1

Motor cable

The applicable standard for interference emissions is EN 61000-6-3. Compliance with this standard is 
achieved through the use of an unscreened motor feed cable.

5.3.2

Control cables

Pay attention to suf

fi

cient distance from powerlines and motor wires to prevent interferences. The 

control cable may not be longer than 30 m. Screened control cables must be used when the cable 
length is longer than 20 m. When using a shielded cable connect the shielding to one side only, i.e. 
only to the control unit with the protective ground (keep cable short and with as little inductance as 
possible!).

5.4

Mains connection

5.4.1

Line voltage

Power from the mains is connected to terminals: PE, L1 and N. Here, it must be strictly observed that 
the mains voltage lies within the allowable tolerance speci

fi

cations (

  Technical data and nameplate 

af

fi

xed to the side).  

A connection between two phase conductors is possible for 3 ~ 230 V supply networks.

Attention!

To activate the on current limitation, you must wait at least 90 seconds after switching off the line 
voltage before switching back on!

5.4.2

Line protection fuse

The mains connection must be fused depending on the used cable, the type of routing, the operating 
conditions and according to the standards applicable on site. The speci

fi

cation for the maximum 

admissible line fuse of the device must be observed (see technical data).

Possible components for the line protection (recommendation):

•

Safety fuses of operating class 

“

gG

”

 (whole range fuse cartridges for general applications according 

to EN 60269-1).

•

Line protection switch with characteristic 

“

C

”

 (according to EN 60898-1).

•

Motor protection switch with overload and short-circuit trigger (according to EN 60947-4-1). Setting 
overcurrent trigger to maximum permissible current of the line.

Operating Instructions 

Fcontrol

 

–

 model series FXET4/6/10AMQ

Electrical installation

L-BAL-E079-GB 1706 Index 008

Part.-No. 

14/87

Summary of Contents for FXET10AMQ
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands