manualshive.com logo in svg

ZIEHL-ABEGG FXET10AMQ, Operating Instructions Manual

Share
Download
ZIEHL-ABEGG FXET10AMQ Operating Instructions Manual Download Page 10

3.6

Storage

•

The device must be stored in its original packaging in a dry and weather-proof room.

•

Avoid exposure to extreme heat and cold.

•

Avoid prolonged storage; we recommend a maximum of one year (consult the manufacturer before 
starting if stored for longer).

3.7

Disposal / recycling

Disposal must be carried out professionally and in an environmentally friendly way in accordance with 
the respective national legal stipulations.

"

Separate the materials by type and in an environmentally friendly way.

"

If necessary, commission a specialist company with the waste disposal.

4

Mounting

4.1

General notes

Attention!

The following points must be complied with during the mechanical installation to avoid causing a defect 
in the device due to assembly errors or environmental in

fl

uences:

•

Before installation remove the device from the packing and check for any possible shipping 
damage! Start-up is not allowed in the case of transport damage!

•

At a weight greater than 25 kg for men / 10 kg for women, the device should be lifted out by two 
persons (according to REFA). The values may differ from country to country.

•

Wear safety shoes and gloves for handling!

•

Assemble the device on a clean and stable base. Do not distort during assembly! Use the 
appropriate mounting devices for proper installation of the unit!

•

A mounting on vibrating base is not permissible, if no data to the vibration strength is made (see 
Technical data)!

•

When mounted onto lightweight walls, there must be no impermissibly high vibrations or shock 
loads. Any banging shut of doors that are integrated into these lightweight walls, can result in 
extremely high shock loads. Therefore, we advise you to decouple the devices from the wall.

•

Do not allow drilling chips, screws and other foreign bodies to reach the device interior!

•

Maintain the stated minimum clearances to ensure unobstructed cooling- air feed as well as 
unobstructed outgoing air discharge (

  minimum space requirement)!

•

The device should be installed in a location where it will not be disturbed, but at the same time can 
be easily accessed!

•

Care must be taken to avoid direct radiation from the sun!

•

The device is designed for vertical installation (cable inlet down). A horizontal or reclined installation 
is only permissible after technical release of the manufacturer!

•

Be sure to observe proper heat dissipation (see Technical data, heat dissipation).

Operating Instructions 

Fcontrol

 

–

 model series FXET4/6/10AMQ

Mounting

L-BAL-E079-GB 1706 Index 008

Part.-No. 

10/87

Summary of Contents for FXET10AMQ
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands