background image

26 

 

is not operated according to the printed installation and operating instructions, including but not   

limited to the use of incorrect fuel. 

 

if the pellet heater and flue system are not serviced as set out in the service and maintenance 

schedule in the printed installation and operating instructions 

 

if the pellet heater is subjected to abuse, neglect, misuse, an accident or water damage 

 

This warranty does not cover   

 

rust due to improper care or lack of maintenance, corrosion, normal wear and tear or flue system 

blockage 

 

Consumer Guarantee 

 

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to 

a  replacement  or  refund  for  a  major  failure  and  for  compensation  for  any  other  reasonably  foreseeable  loss  or 

damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality 

and the failure does not amount to a major failure. 

 

Park – Tec Engineering Pty Ltd will not be liable for any act, default, omission or representation made by any person other 

than our employees, alterations made to the product not performed by us, damage or defects due to unusual or non  – 

recommended use or damage or loss caused by any factors beyond our control. 

 

Subject  to  the  above  paragraphs,  all  express  or  implied  representations,  conditions,  statutory  guarantees, 

warranties and provisions  (whether based on statute,  common law or otherwise), relating to this warranty, that 

are not contained in it, are excluded to the fullest extent permitted by law. 

 

Nothing  in  this  warranty  excludes,  restricts  or  modifies  any  condition,  warranty,  statutory  guarantee,  right  or 

remedy, implied or imposed by common law, statute or regulation, which cannot be lawfully excluded, restricted 

or modified. 

 

For Customer Reference (file in a safe place)

 

 

Purchased from __________________________________   

 

Date Purchased _____/_______/_________              Record Serial Number ______________________ 

 

N.B Satisfactory proof of purchase like your sales docket must be kept for any claim under this warranty to 

be enforceable.   

Service Contact Point

 – Please contact your place of purchase for warranty repairs or service.   

 

Made in China 

Imported by G.L.G. Australia Pty Ltd 

Build A2, Campus Business Park, 350-374 Parramatta Road, Homebush, NSW 2140     

Tel – 02 9735 4111 or 1300 301 392 for your nearest store. 

Email – [email protected] 

 

Summary of Contents for KOMFORT



























Reviews: