ZF DUOPLAN 2K120 Operating Instructions Manual Download Page 7

 

  Safety 

EN 4161.758.101m – 2018-09 

 

Observe the following points: 

 

Employ authorized, trained and instructed staff. 

 

Observe technical provisions. 

 

Only use genuine ZF spare parts. 

 

Only use genuine ZF accessories. 

 

Only use genuine ZF special tools. 

 

Unauthorized changes and modifications lead to 
the expiry of the operator's license, warranty or 
guarantee. 

In case of damage, contact ZF and have the 
following information on the product to hand: 

 

Type 

 

Parts list [BoM] number 

 

Serial number 

 

Kilometer reading 

 

Description of damage 

Observe safety instructions, valid safety regulations 
and legal requirements to prevent malfunctions 
and damage. 

The country-specific safety regulations, accident 
prevention regulations and environmental 
protection provisions also apply. 

Wear workwear in accordance with safety 
requirements for all work. Depending on the work, 
also wear personal protective equipment. 

After completing the work, check correct function 
and functional security. 

Handling of ZF product 

Unauthorized changes and modifications may 
impair functional security. 

Changes, modifications and applications are only 
permitted with the written approval of ZF 
Friedrichshafen AG. 

Observe the following when working on the ZF 
product: 

 

Secure workspace. 

 

Only carry out work at the unit when in a 
voltage-free state. 

 

Protect unit against being started accidentally. 
Attach information sign in a clearly visible 
position. 

 

Perform work when motor is switched off. 

 

Protect motor against being started accidentally. 
Attach information sign in a clearly visible 
position. 

 

Do not stand beneath a suspended load. 

 

Do not work on a suspended load. 

 

Only use permitted means of transport and 
lifting appliances with sufficient load-bearing 
capacity. 

 

Close open pipelines and hoses and avoid 
damage. 

 

Observe tightening torques. 

 

Protect cables against mechanical damage. 

Noise 

Noise may cause irreversible damage to hearing. 

The perception of acoustic signals, warning calls 
or sounds warning of impending danger is 
impaired by noise. 

Observe the following when working on the ZF 
product: 

 

Avoid noise. 

 

Wear ear protection. 

Operating supplies and auxiliary materials 

Operating supplies and auxiliary materials may 
cause permanent damage to health and 
environmental damage. 

Observe the following when selecting operating 
supplies and auxiliary materials: 

 

Health risks 

 

Environmental compatibility 

 

Material safety data sheets 

Observe the following when handling operating 
supplies and auxiliary materials: 

 

Store operating supplies and auxiliary materials 
in suitable and correctly labeled containers. 

 

Seek medical help in case of injuries due to hot, 
cold or caustic operating supplies or auxiliary 
materials. 

Observe the following to protect the environment: 

 

Collect leaking operating supplies and auxiliary 
materials in containers of a sufficient size. 

 

Observe disposal regulations. 

 

Observe material safety data sheets. 

Summary of Contents for DUOPLAN 2K120







































Reviews: