ZF AV 133 Repair Instructions Download Page 4

Page: 4 / 138

8.10

......................................................................................................................

8.11

......................................................................................................................................

Assembly

....................................................................................................................

9.1

Install input

..........................................................................................................................................

9.2

Assemble differential

........................................................................................................................

9.3

Setting backlash and differential bearing rolling torque and checking axial run-out and

contact pattern.

..................................................................................................................................

9.4

Install shaft seal onto the drive

......................................................................................................

9.5

Assemble and install left portal drive

...........................................................................................

9.5.1

Assemble left portal drive

...............................................................................................................

9.5.2

Install left portal drive

.......................................................................................................................

102

9.6

Assemble and install right portal drive

........................................................................................

103

9.6.1

Assemble right portal drive

.............................................................................................................

103

9.6.2

Install right portal drive

....................................................................................................................

116

9.7

Install breather neck

.........................................................................................................................

117

9.8

Install breather

....................................................................................................................................

118

9.9

Install tachometer

..............................................................................................................................

118

9.10

Assemble and install hub

................................................................................................................

120

9.10.1

Assembling hub

.................................................................................................................................

120

9.10.2

Install hub

............................................................................................................................................

124

9.11

Install brake

.........................................................................................................................................

127

9.12

Install mounting parts

.......................................................................................................................

129

9.13

Filling oil

...............................................................................................................................................

131

Testing, Measuring, Adjusting

.....................................................................................

133

10.1

Check contact pattern

......................................................................................................................

133

10.1.1

Contact pattern on crown wheel shifted towards the root

.....................................................

134

10.1.2

Contact pattern on the crown wheel shifted towards the tip

................................................

135

Annex

.........................................................................................................................

136

11.1

Overview of revisions

........................................................................................................................

136

Table of Contents

EN 4472.751.001 - 2015-11

Summary of Contents for AV 133











































































































































Search results

Summary of Contents for AV 133

Reviews:

Related manuals for AV 133

Brands by name

Popular brands

ZF AV 133, Repair Instructions

Search results

Summary of Contents for AV 133

Reviews:

Related manuals for AV 133

Brands by name

Popular brands