ZF AV 133 Repair Instructions Download Page 3

Page: 3 / 138

.......................................................................................................................

1.1

Document overview

..........................................................................................................................

Safety Instructions

......................................................................................................

2.1

General safety instructions

..............................................................................................................

2.2

Signal words and symbols

..............................................................................................................

Notes on Repairs and Assembly

.................................................................................

3.1

General notes

......................................................................................................................................

3.2

Cleaning the ZF product

..................................................................................................................

3.3

Dismantling the ZF product

............................................................................................................

3.4

Assembling the ZF product

............................................................................................................

3.5

Cleaning parts

....................................................................................................................................

3.6

Reusing parts

......................................................................................................................................

3.7

Replacing parts

..................................................................................................................................

3.8

Reworking parts

.................................................................................................................................

Technical Data

............................................................................................................

4.1

Oil grade

..............................................................................................................................................

4.2

Type plate

.............................................................................................................................................

Setting Data

...............................................................................................................

Tightening Torques

.....................................................................................................

Workshop Equipment

.................................................................................................

7.1

Special tools

........................................................................................................................................

7.2

Standard tools and fixtures

.............................................................................................................

7.3

Operating supplies and auxiliary materials

.................................................................................

Dismantling

................................................................................................................

8.1

Clamp the axle

...................................................................................................................................

8.2

Drain oil

................................................................................................................................................

8.3

Remove mounting parts

...................................................................................................................

8.4

Removal of brake

...............................................................................................................................

8.5

Remove and dismantle hub.

...........................................................................................................

8.5.1

Remove hub

........................................................................................................................................

8.5.2

Dismantling hub

.................................................................................................................................

8.6

Remove tachometer

..........................................................................................................................

8.7

Remove and dismantle left portal drive

.......................................................................................

8.7.1

Remove left portal drive

...................................................................................................................

8.7.2

Dismantling left portal drive

...........................................................................................................

8.8

Remove breather

................................................................................................................................

8.9

Remove and dismantle right portal drive.

...................................................................................

8.9.1

Remove right portal drive

................................................................................................................

8.9.2

Dismantle right portal drive

............................................................................................................

Table of Contents

EN 4472.751.001 - 2015-11

Summary of Contents for AV 133











































































































































Search results

Summary of Contents for AV 133

Reviews:

Related manuals for AV 133

Brands by name

Popular brands

ZF AV 133, Repair Instructions

Search results

Summary of Contents for AV 133

Reviews:

Related manuals for AV 133

Brands by name

Popular brands