manualshive.com logo in svg

ZF AV 133, Repair Instructions


Share
Download
background image

1.

Bolt in two pieces AA00.844.345 [Load ring]

(1) onto the portal housing.

2.

Grease the O‑ring (2) and insert it into the

annular groove on the portal housing.

3.

Push the stub shaft with the pin showing

inwards into the drive gear of the portal drive.

Thereby take up the shaft washer with the

pin on the drive gear.

4.

Push the stub shaft into the axle housing and

bring the portal housing into contact position

with the axle housing.

Fig. 237  

5.

Support axle from below (1).

6.

Fix portal drive with Torx screws.

Tightening torque: 185 Nm

Fig. 238  

9.7

Install breather neck

1.

Push the breather neck into the hole on the

axle housing so that an edge of the hexagon

is parallel to the portal housing.

2.

Risk of injury due to parts flying away.

Slight or moderate injury possible.

ð

Wear protective goggles.

Force the breather neck with a sleeve or a

tube into the axle housing.

Fig. 239  

Assembly

EN 4472.751.001 - 2015-11

117

Summary of Contents for AV 133











































































































































Reviews:

No comments

Related manuals for AV 133

Brands by name

Popular brands

Load more brands