Zero Motorcycles S 2021 Owner'S Manual Download Page 112

Page: 112 / 160

Troubleshooting

7.8

General Troubleshooting

SYMPTOM

POTENTIAL CAUSE

POTENTIAL SOLUTION

Motorcycle does not turn on

Power Pack not charged. Key not properly engaged.
Motor stop switch turned OFF. Fault code set.

Charge Power Pack. Recheck key in ignition, turn OFF/ON
again. Press the motor stop Switch ON button.

Charger not working

A/C power missing. Fault code set.

Check A/C outlet for power, A/C source check
fuse/voltage.

Handlebars wobbly (shimmy)

Incorrect tire pressure.

Inflate to correct tire pressure. See

page 6.16

Deformed front tire.

Replace/balance front tire with the same tire supplied from
the factory.

Bald tire (excess wear).

Replace/balance tire with the same tire supplied from the
factory.

Loose headset bearings.

Inspect the headset for wear or damage, replace any worn
or damaged parts. Tighten the headset pre-load.

Zero Owner's Manual (S and DS).book Page 8 Monday, September 21, 2020 11:43 AM

Summary of Contents for S 2021

































































































































































Search results

Summary of Contents for S 2021

Reviews:

Related manuals for S 2021

Brands by name

Popular brands

Zero Motorcycles S 2021, Owner'S Manual

Search results

Summary of Contents for S 2021

Reviews:

Related manuals for S 2021

Brands by name

Popular brands