background image

INSTALLATION

MOUNTING THE RANGEHOOD

1. This range hood is mounted under a 

kitchen cabinet unit.

2. Select preferred duct location on rear or 

top of unit. (See page 6 & 7 for ducting 
conversion options)

3. Begin installation by temporarily 

unscrewing and removing the bottom 
splash panel.

4. Reinforce cabinet base with 1x2 wood 

strips if additional strengthening is 
required.

5. Temporarily position the range hood in 

the desired mounting location.
Measure and mark the mounting holes,
duct and electrical access locations with 
a pencil.

6. Drill/cut out the required openings for 

duct and electrical access; make sure the
duct opening is large enough to apply 
duct tape.

7. Fasten hood onto cabinet with screws 

and washers provided.

8. Install electrical.

9. Install duct work and duct-tape.

10. Reinstall the bottom splash panel.

11. Power up hood and check for leaks 

around duct-tape.

INSTALLATION

MOUNTING THE RANGEHOOD

ELECTRICAL

All Electrical work must by performed by qualified electrician or person with similar technical
know how and background.

For personal safety, remove house fuse or open circuit breaker before beginning installation.
Do not use extension cord or adapter plug with this appliance.

Follow National electrical codes or prevailing local codes and ordinances.

Electrical Supply:

This appliance requires a 120V 60Hz electrical supply., and connected to an individual, properly
grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring
must be 2 wire w/ ground. Please also refer Electrical Diagram labeled on product.

Cable Lock:

A cable locking connector (not supplied) might also be required by local codes. Check with local
requirements and codes, purchase and install appropriate connector if necessary.

Cable Lock

WARNING 

Models: AK6500, AK6536, AK6542, AK2500, AK2536   

Page 5

Models: AK6500, AK6536, AK6542, AK2500, AK2536   

Page 4

duct/silver 
tape

6. Duct

opening
cutout

4. Add 1x2 

wood strips

3. Splash

bottom panel

Summary of Contents for AK6500

















Reviews: