background image

GB-17

G2001

G

B

Limited warranty

Should any failure occur on the product under normal 
operating conditions within the applicable warranty 
period, the failed part will be replaced or repaired free 
of charge by a ZENOAH authorized dealer.

WARRANTY PERIOD:

 Six (6) months after purchased 

by end-user subject to 12 months from produced month. 
(30 days If used for rental purpose)

THE PURCHASER SHALL BEAR COSTS OF TRANS-
PORTING THE UNIT TO AND FROM THE ZENOAH 
DEALER. 

THE PURCHASER SHALL NOT BE CHARGED FOR 
DIAGNOSTIC LABOR WHICH LEADS TO THE DETER-
MINATION THAT A WARRANTED PART IS DEFECTIVE, 
IF THE DIAGNOSTIC WORK IS PER FORMED AT THE 
ZENOAH DEALER.

THE PURCHASER OR OWNER IS RESPONSIBLE FOR 
THE PERFORMANCE OF THE REQUIRED MAINTE-
NANCE AS DEFINED BY THE MANUFACTURER IN THE 
OWNER/OPERATOR MANUAL.

ANY WARRANTED PART WHICH IS NOT SCHEDULED 
FOR REPLACEMENT AS REQUIRED MAINTENANCE, 
OR WHICH IS SCHEDULED ONLY FOR REGULAR 
INSPECTION TO THE EFFECT OF REPAIR OR “RE-
PLACE AS NECESSARY” SHALL BE WARRANTED FOR 
THE WARRANTY PERIOD. ANY WARRANTED PART 
WHICH IS SCHEDULED FOR REPLACEMENT AS RE-
QUIRED MAINTENANCE SHALL BE WARRANTED FOR 
THE PERIOD OF TIME UP TO THE FIRST SCHEDULED  
REPLACEMENT POINT FOR THE PART.

ANY REPLACEMENT PART THAT IS EQUIVALENT IN 
PERFORMANCE AND DURABILITY MAY BE USED IN 
NON-WARRANTY MAINTENANCE OR REPAIRS, AND 
SHALL NOT REDUCE THE WARRANTY OBLIGATION 
OF THE COMPANY.

THE COMPANY IS LIABLE FOR DAMAGES TO OTHER 
ENGINE COMPONENTS CAUSED BY THE FAIRURE 
OF A WARRANTED PARTS STILL UNDER WARRAN-
TY.

THE WARRANTY DOES NOT APPLY TO

 THOSE UNITS 

WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF 
INSTRUCTION LISTED IN THE OWNER/OPERATOR 
MANUAL FOR PROPER USE AND MAINTENANCE OF 
THE UNITS ACCIDENT MISHANDLING, ALTERATION, 
ABUSE, IMPROPER LUBRICATION, USE OF ANY 
PARTS OR ACCESSARIES OTHER THAN THOSE 
SPECIFIED BY THE COMPANY, OR OTHER CAUSES 
BEYOND THE COMPANY'S CONTROL.

THIS WARRANTY DOES NOT COVER

 THOSE PARTS 

REPLACED BY NORMAL WEAR OR HARMLESS 
CHANGES IN THEIR APPEARANCE.

THERE ARE NO OTHER EXPRESS WARRANTIES.

ANY IMPLIED WARRANTY

 is limited to the duration of 

the limited warranty. Otherwise, this limited warranty is 
in lieu of all other expressed or implied warranties, in-
cluding any warranty of 

FITNESS FOR A PARTICULAR 

PURPOSE OR USE

 and any implied warranty 

MER-

CHANTABILITY

 otherwise applicable to this product.

LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL 
DAMAGE UNDER ANY AND ALL WARRANTIES ARE 
EXCLUDED.

IF YOU NEED TO OBTAIN MORE INFORMATION, 
PLEASE CALL YOUR NEAREST SERVICE CENTER, OR 
CHECK PLEASE ZENOAH WEB SITE 
http://www.zenoah.net

Summary of Contents for G2001



















Reviews: