background image

GB-8

HT2310 / CHT2310

7. While operating the machine be

always sure of a safe and secure
operating position especially
when using steps or a ladder.

 

 IF SOMEONE COMES

1. Guard against hazardous situa-

tions at all times. Warn adults to
keep pets and children away from
the area. Be careful if you are ap-
proached. Injury may result from
flying debris.

2. If someone calls out or otherwise

interrupts you while working, al-
ways be sure to turn off the en-
gine before turning around.

MAINTENANCE

1. In order to maintain your product

in proper working order, perform
the maintenance and checking
operations described in the
manual at regular intervals.

2. Always be sure to turn off the en-

gine before performing any main-
tenance, checking procedures or
working on the machine.

 WARNING

The metallic parts reach high tem-
peratures immediately after stop-
ping the engine.

3. When replacing the cutting at-

tachment or any other part, or
when replacing the oil or any lu-
bricant, always be sure to 

use

only ZENOAH  products or
products which have been cer-
tified by ZENOAH for use with
the ZENOAH product.

4. In the event that any part must be

replaced or any maintenance or
repair work not described in this
manual must be performed,
please contact a representative
from the store nearest ZENOAH
authorized servicing dealer for
assistance.

5. Do not use any accessory or at-

tachment other than those bear-
ing the ZENOAH mark and rec-
ommended for the unit.

 5. For safe operation

6. Under no circumstances should

you ever take apart the product
or alter it in any way. Doing so
might result in the product be-
coming damaged during opera-
tion or the product becoming un-
able to operate properly.

HANDLING FUEL

1. The engine of the ZENOAH prod-

uct is designed to run on a mixed
fuel, which contains highly flam-
mable gasoline. Never store cans
of fuel or refill the tank of the unit
in any place where there is a
boiler, stove, wood fire, electrical
sparks, welding sparks, or any
other source of heat or fire which
might ignite the fuel.

2. Never smoke while operating the

unit or refilling its fuel tank.

3. When refilling the tank, always

turn off the engine and allow it to
cool down. Take a careful look
around to make sure that there are
no sparks or open flames any-
where nearby before refueling.

4. Wipe spilled fuel completely us-

ing a dry rag if any fuel spillage
occurs during refueling.

5. After refueling, screw the fuel cap

back tightly onto the fuel tank and
then carry the unit to a spot 3 m
or more away from where it was
refueled before turning on the
engine.

6.  Do not inhale fuel fumes as they

are toxic.

TRANSPORTATION

1. When hand-carrying the product,

cover over the cutting part if nec-
essary, lift up the product and
carry it paying attention to the
blade.

2. Never transport the product over

rough roads over long distances
by vehicle without removing all
fuel from the fuel tank. If doing so,
fuel might leak from the tank dur-
ing transport.

Summary of Contents for CHT2310
















Reviews: