background image

GB-12

HT2310 / CHT2310

 WARNING

Make sure that the engine has stopped and is cool
before performing any service to the machine. Con-
tact with moving cutting head or hot muffler may
result in a personal injury.

BLADE

Check the blade and the fasteners for looseness,

cracking, or bending.

Check the cutting edges and reform with a flat file.

Point :
1. Keep the end corner sharp.
2. Round the root of the edge.
3. Do not use water when using a grinder.

SAFETY LOCK

 WARNING

  

Stop operation when the safety lock is de-
fective.

Safety lock is the device not to accelerate the throttle

lever without intention. While pushing the safety lock,
you can accelerate the throttle lever.

           

1. Check if the throttle lever does not move when you do

not push the safety lock.

2. Check if the throttle lever moves when you grasp or

release it while pushing the safety lock.

3. Check if the safety lock returns to its original position

when you release your hand from safety lock.

If you find any defects at the checks above, contact

your nearest servicing dealer for repair.

8. Maintenance

(1) Safety lock

Every Every Every

25

50

100

       System/components

         Procedure

Before

hours hours hours                   Note

use

after

after

after

fuel leaks, fuel spillage

wipe out

fuel tank, air filter, fuel filter

inspect/clean

replace, if necessary

see adjusting

replace carburetor

idle adjusting screw

idling speed

if necessary

clean and readjust

GAP: 0.6 ~ 0.7 mm

spark plug

plug gap

replace, if necessary

cylinder fins, intake air cooling vent

clean

muffler, spark arrester, cylinder exhaust port

clean

throttle lever, ignition switch

check operation

replace if

cutting parts

something’s wrong

gear case

grease

screws/nuts/bolts

tighten/replace

not adjusting screws

debris guard

make sure to attach

ENGINE

SHAFT

Summary of Contents for CHT2310
















Reviews: