background image

• IF SOMEONE COMES
1. Guard against hazardous situations at all times.

Warn adults to keep pets and children away
from the area. Be careful if you are approached.
Injury may result from flying debris.

2. If someone calls out or otherwise interrupts you

while working, always be sure to turn off the
engine before turning around.

MAINTENANCE

1. In order to maintain your product in proper

working order, perform the maintenance and
checking operations described in the manual at
regular intervals.

2. Always be sure to turn off the engine before

performing any maintenance or checking
procedures.

The metallic parts reach high temperatures
immediately after stopping the engine.

3. When replacing the cutting attachment or any

other part, or when replacing the oil or any
lubricant, always be sure to use only ZENOAH
products or products which have been
certified by ZENOAH for use with the
ZENOAH product
.

4. In the event that any part must be replaced or

any maintenance or repair work not described in
this manual must be performed, please contact a
representative from the store nearest ZENOAH
authorized servicing dealer for assistance.

5. Do not use any accessory or attachment other

than those bearing the ZENOAH mark and
recommended for the unit.

6. Under no circumstances should you ever take

apart the product or alter it in any way. Doing so
might result in the product becoming damaged
during operation or the product becoming unable
to operate properly.

WARNING

5. For safe operation

9

Summary of Contents for BT251

























Reviews: