background image

7. Fuel

13

again for at least one minute. As some
oils may be difficult to agitate depending
on oil ingredients, sufficient agitation is
necessary for the engine to last long. Be
careful that, if the agitation is insufficient,
there is an increased danger of early
piston seizing due to abnormally lean
mixture.

5. Put a clear indication on the outside of the

container to avoid mixing up with gasoline
or other containers.

6. Indicate the contents on outside of

container for easy identification. 

FUELING THE UNIT

1. Untwist and remove the fuel cap. Rest the

cap on a dustless place.

2. Put fuel into the fuel tank to 80% of the full

capacity.

3. Fasten the fuel cap securely and wipe up

any fuel spillage around the unit.

1. Select bare ground for fueling.
2. Move at least 10feet (3meters) away from

the fueling point before starting the
engine.

3. Stop the engine before refueling the unit.

At that time, be sure to sufficiently agitate
the mixed gasoline in the container.

FOR YOUR ENGINE LIFE, AVOID;
1. FUEL WITH NO OIL(RAW GASOLINE) –

It will cause severe damage to the internal
engine parts very quickly.

2. GASOHOL – It can cause deterioration of

rubber and/or plastic parts and disruption
of engine lubrication.

3. OIL FOR 4-CYCLE ENGINE USE – It can

cause spark plug  fouling, exhaust port
blocking, or piston ring sticking.

4. Mixed fuels which have been left

unused for a period of one month or
more 
may clog the carburetor and result
in the engine failing to operate properly.

5. In the case of storing the product for a

WARNING

long period of time, clean the fuel tank
after rendering it empty. Next, activate the
engine and empty the carburetor of the
composite fuel.

6. In the case of scrapping the used mixed

oil container, scrap it only at an authorized
repository site.

As lot details of quality assurance, read the
description in the section Limited Warranty
carefully.  Moreover, normal wear and
change in product with no functional
influence are not covered by the warranty.
Also, be careful that, if the usage in the
instruction manual is not observed as to the
mixed gasoline, etc. described therein, it
may not be covered by the warranty.

NOTE

Summary of Contents for BT251

























Reviews: