background image

8. Maintenance

IMPORTANT

•  Note that using any spark plug other than those des

-

ignated may result in the engine failing to operate 
properly or in the engine becoming overheated and 
damaged.

•  To install the spark plug, first turn the plug until it is 

finger tight, then tighten it a quarter turn more with a 
socket wrench.

Tightning torque: 
  9.8~11.8N.m. 
  (1.0~1.2kgm)

 GEAR CASE

•  The reduction gears are lubricated by multipurpose, 

lithium-based grease in the gear case. Supply new 
grease every 25 hours of use or more often depend-
ing on the job condition. 

•  Remove the bolt opposit to the grease nipple before 

installing new grease to arrange for old grease to exit. 

WARNING

Make sure that the engine has stopped and is cool 
before performing any service to the machine. Con-
tact  with  moving  cutting  head  or  hot  muffler  may 
result in a personal injury.

 AIR FILTER

The air filter, if clogged, will reduce the engine perfor-
mance. Check and clean the filter element in warm, 
soapy water as required. Dry completely before installing. 
If the element is broken or shrunk, replace with a new 
one.

(1) Air filter

 FUEL FILTER

When the engine runs short of fuel supply, check the fuel 
strainer for blockage.

(1) Fuel strainer

 SPARK PLUG

Starting failure and misfiring are often caused by a fouled 
spark plug. Clean the spark plug and check that the plug 
gap is in the correct range. For a replacement plug, use 
the correct type specified by ZENOAH.

0.6~0.7mm

REPLACEMENT PLUG IS 
A NGK BPMR7A.

GB-12

BC3450DW / BC4350DW

BC3450DW_4350DW_GB_cs5.indd   12

17/09/05   17:04

Summary of Contents for BC3450DW


















Reviews: