Zelmer ZVC545CQ, User Manual

Page: 50 / 52

56
ZVC545-001_v01
18 Parquet brush “BNB” (Brush Natural Bristle) (only in
model ZVC545AP, ZVC545CQ)
Is used to clean and polish hard, scratch sensitive surfaces
such as wooden floors, floor panels, parquet, marble,
tiles, etc.
Delicate and soft natural bristles ensure maximum
vacuum effectiveness and protects against scratching
the cleaned surface.
19 Small nozzle
20 Small brush
21 Crevice nozzle
22 Switchable combination brush
23 Mini turbobrush (only in model ZVC545CA, ZVC545CQ)
24 Suction nozzle for mattresses cleaning (only in model
ZVC545AP)
25 Brush for collecting pet hair from carpets (only in model
ZVC545CA, ZVC545CQ)
26 Accessory holder
27 Holder screws
28 Battery-powered electrobrush (only in model ZVC545CQ)
Preparing the vacuum cleaner
for operation
1 Insert the curved hose end in the opening of the vacuum
cleaner and gently press. A characteristic click indicates that
the hose has been properly installed.
2
Connect the other end of the hose (handle) with the
telescopic suction tube. In order to do so press the locking
device “A” and slide the tube into the hose handle so that
the locking device “A” is blocked in opening “B” .
3 Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/ pull the tube
together.
4
Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5 Use combination carpet & floor brush for vacuuming both
hard surfaces and carpets. To clean hard surfaces – wooden
floors, plastic floors, ceramic tiles etc. pull out the brush by
pressing the switch on the combination brush according to
the figure . Retract the brush when vacuuming carpets
(set the switch in “ ”).
6
The accessories may be attached to the accessory
holder in the suction hose handle. This way they will be
available for use at any time.
7 Pull the plug and cord (3) out of the vacuum cleaner.
Do it smoothly (do not tug) to avoid cord tangling and
blocking in the vacuum body.
While puling out the cord pay attention to the
yellow stripe which signals the end of the cord.
Further attempts (pulling on cord) may result in
damaging the cord.
8 Plug in the appliance.
B
Before operation make sure that the SAFBAG bag is
installed in the vacuum cleaner chamber and that inlet filter
and the HEPA outlet filter is installed in the appliance.
9
Switch on the vacuum cleaner by pressing the “on/off”
button (8) .
10 The vacuum cleaner is equipped with electronic power
regulator allowing a stepless regulation of vacuum cleaner
power. The power regulation is performed with a slider.
Moving the slider right or left will increase or reduce
the suction power.
The following slider positions are recommended:
– for delicate fabrics such as curtains, etc.
– for upholstered furniture
– for carpets and floor coverings
– for hard surfaces such as floor, tiles,
parquet etc.
The power may also be adjusted individually depending on
the type of surface, vacuum effectiveness and suction power
of the switchable combination brush.
11 The vacuum cleaner features the parking system and
auto start. Use this feature to temporarily turn off the vacuum
cleaner without having to use the power button by hooking
your combination carpet & floor brush on the parking system.
For a quick break during vacuum cleaning, simply hook your
combination carpet & floor brush on the parking system (2)
in a horizontal position. The vacuum cleaner will turn off
automatically. The dust bag full indicator (7) will come on.
12
The vacuum cleaner is also equipped with a mechanical
suction power regulator (11) located on the suction hose
handle. It can be used to adjust the suction power slightly for
a short time without having to use the slider (6) .
Filter disassembly
Before changing the filters make sure that the vacuum cleaner
is switched off and unplugged from the mains supply.
INLET FILTER
1 Release the catch of front cover (10) and open it.
2
Remove the SAFBAG dust bag module from the vacuum
cleaner chamber.
3 Put out the cover of inlet filter together with installed inlet
filter from the guide rails located on back wall of vacuum
cleaner chamber.
4
Take out the inlet filter from the inlet filter cover.
5 Put the new filter into inlet filter cover (16) . Pay attention
whether the edges of filter cling closely to the cover of filter.
6 The cover of inlet filter (16) together with installed filter
press home into guide rails to the previous location.
C