27
ZVC382-001_v01
4
Remove the “CYKLON” dust container from the vacuum
cleaner chamber.
5
Pull aside the fastenings on the “CYKLON” dust container
and open the container. Empty the dirt from the container.
After performing this activity, check the basic
HEPA H10 filter and if necessary clean or
replace the filter.
6
Close the cover of the “CYKLON” dust container, firmly
press the fastenings until you hear a characteristic “click”.
The container must be tightly closed.
Otherwise the dust might enter the vacuum
cleaner chamber and the suction power will be
reduced.
7
Insert the empty “CYKLON” dust container into the
vacuum cleaner chamber.
8
Close the cover by pressing it until you hear
a characteristic click.
Filter disassembly
The vacuum cleaner is equipped with a filter element with
cyclone filtration which allows for vacuuming without the
traditional dust bag. A characteristic feature of the cyclone
filter is the use of the air stream whirl to separate solid dirt.
The separation of dirt takes place in the part of the container
with the circle cross section in which the whirling air pushes
the dirt on the wall of the container and next through an
opening to the adjacent chamber of the container. The
initially cleaned air is directed to the cone shaped HEPA
H10 filter which retains even the finest dirt fractions. The
HEPA H10 filter is equipped with a mesh protection which
limits the accumulation of dirt on the operating surface of the
filter, due to which the service life of the HEPA H10 filter is
longer.
T
he basic HEPA (High Efficiency Particulate Air) washable
class H10 filter is located at the outlet of the cyclone filter
container. The HEPA H10 washable filter is made of a special
filtration material which enables to rinse the filter under
running water once it becomes dirty and to reuse the filter.
An outlet HEPA class H11 filter (non-washable) is located at
the outlet of the vacuum cleaner.
Before changing the filters make sure that the vacuum
cleaner is switched off and unplugged from the mains supply.
BASIC HEPA H10 FILTER
It is necessary to periodically clean the basic HEPA H10 filer
from fine dust fractions.
Dismantle the “CYKLON” dust container and empty the
container according to the instructions in section
(E)
.
1
Turn the basic HEPA H10 filter in the UNLOCK direction
and remove the filter.
2
Remove the protective mesh of basic filter
(14)
.
●
Clean the mesh and dry it thoroughly. Replace the mesh
if damaged.
D
Due to safety reasons it is prohibited to install
a moist protective mesh.
●
Clean the pleats of the basic HEPA H10 filter
(13)
. The
filter can be washed under running water. Thoroughly dry
the filter. In case of damage to the filter pleat, the filter
must be replaced with a new one.
Due to safety reasons it is prohibited to install
a moist or damaged basic HEPA H10 filter (13).
3
After cleaning and drying the protective mesh and the
basic HEPA H10 filter, install the protective mesh on the
HEPA H10 filter and insert the whole unit to the “CYKLON”
dust container.
4
Press the interlock button and turn the basic HEPA H10
filter
(13)
in the LOCK direction.
Insert the “CYKLON” dust container together with the
installed basic HEPA H10 filter
(13)
into the vacuum cleaner
chamber and close the cover by pressing it until you hear
a characteristic “click” according to section
(E)
.
HEPA H11 OUTLET FILTER
1
To replace the HEPA H11 filter lift the vacuum cleaner
handle and open the accessory compartment.
2
Grab the filter cover by the fastening, firmly pull with the
thumb and lift it upwards.
3
Remove the HEPA H11 filter case and replace it with
a new one. The HEPA filter ensures an effective operation of
the vacuum cleaner for about 1 year.
4
Insert the cover so that the two protrusions in the lower
part of the cover are inserted in the openings of the vacuum
cleaner body, press the filter cover so that the rear fastenings
snap shot on the body.
INLET FILTER
●
Release the upper cover fastening
(12)
and open the
cover.
●
Remove the SAFBAG dust bag module/the “CYKLON”
dust container from the vacuum cleaner chamber.
1
Slide the inlet filter casing with the installed inlet filter
from the tracks on the back side of the vacuum cleaner
chamber.
2
Remove the inlet filter
(19)
from the inlet filter casing.
3
Place the new filter in the inlet filter casing
(20)
with the
material side directed towards the inside of the casing.
4
Slide the inlet filter casing
(20)
together with the filter in
the tracks until stop to the previous position.
Always replace a damaged inlet filter (19) with
a brand new, original one.
●
Insert the SAFBAG dust bag module/the “CYKLON” dust
container into the vacuum cleaner chamber.
●
Close the cover by pressing it until you hear
a characteristic click.
F
G
Summary of Contents for ZVC382ST
Page 23: ...Notes ...
Page 24: ...Notes ...
