Zelmer ZVC315HP, User Manual

Page: 62 / 64

68
ZVC315-001_v02
16 Dust container “CYCLONE” (which is a removable
segment of the vacuum cleaner)
17 Dust container cone “CYCLONE” (mounted in dust
container “CYCLONE”)
18 Switchable sucker-brush sweeper
19 Gap sucker
20 Small brush sweeper
21 Small sucker
22 “BNB” Parquet brush sweeper (Brush Natural Bristle).
Available only in case of ZVC315HP version.
Used for cleaning and polishing of hard, scratch-sensitive
surfaces such as wood flooring, panels, parquet, marble,
tiles, etc.
Delicate and soft bristles of Natural origin provide
maximum vacuuming efficiency and protects against
scratches on the surface.
Prepare the vacuum cleaner to use
B
1 Insert the tip of the suction hose to the vacuum cleaner
inlet. The characteristic “click” indicates a properly fitted hose.
2 The second end of the hose (a handle) connect to
telescopic suction tube.
3 Set the telescopic suction tube to the desired length by
sliding the slider according with arrow and put out / slide out
the tube.
4 On the other end of the suction tube install the
appropriate sucker or brush.
5 Use combination carpet & floor brush for vacuuming both
hard surfaces and carpets. To clean hard surfaces – wooden
floors, plastic floors, ceramic tiles etc. pull out the brush by
pressing the switch on the combination brush according
to the figure . Retract the brush when vacuuming
carpets (set the switch in “ ”).
6
Catch the connection cable plug (3) and draw it out from
the vacuum cleaner.
When drawing out the power cable you have to
pay attention to yellow band indicating the end
of the cable drawn out. Further attempts (jerks)
may lead to damage of the cable.
7 Plug the cord into an AC outlet.
Before you start vacuum cleaner make sure whether the dust
container “CYCLONE” is mounted in chamber of the vacuum
cleaner, and whether the inlet and outlet filters are mounted
in the vacuum cleaner.
8
Start the vacuum cleaner by pressing On/Off button (4) .
9 Vacuum cleaner is equipped with electronic power
regulator, which - during the vacuuming - can smooth control
the suction power of vacuum cleaner. By turning the knob (4)
right or left – you can increase or decrease the suction power.
10
Vacuum cleaner is also equipped in mechanical control
of suction power (9) , which is located on the handle of the
hose. It can temporarily slightly adjust the suction power,
without adjustment done with knob (4) .
Disassembly/assembly of “CYCLONE”
dust container
Vacuum cleaner is equipped in removable dust container
“CYCLONE” (which is a removable segment of vacuum
cleaner), which accumulates contaminants. As soon as the
“CYCLONE” dust container is full, it should be emptied.
Vacuum cleaner is equipped with a safety
valve which is located in the chamber of the
“CYCLONE” dust container. The valve is
activated (open) automatically when a total
jam (occlusion) occurs on the sucking hose
or this happens to equipment connected to it,
as well as in the case of excessive overfill of
“CYCLONE” dust container. When the valve
is open you can hear a characteristic sound
(“a sound of flutter”) in the vacuum cleaner.
1
Vacuum cleaner is equipped with a dust container
“CYCLONE” full indicator (5) . When the gap of dust container
“CYCLONE” full indicator is totally filled with red mark during
operation (vacuum cleaner operates at full power and
sucker nozzle or brush is upraised over cleaned surface)
so this informs that there is a need to empty the dust bin
“CYCLONE”. The dust container “CYCLONE” full indicator
(5) may work also in the case of clogging of the suction hose
or clogging of equipment connected to the hose.
2 Switch off the vacuum cleaner by pressing On/Off
button (4) .
3 Take off the cable connection plug from the wall outlet.
4 Press the two side buttons on the hose end, then remove
the hose end from vacuum cleaner inlet hole.
5
Raise the hook to unlock the dust container “CYCLONE”
(7) and remove dust container “CYCLONE” (16) from the
vacuum cleaner.
6 Move the dust container “CYCLONE” on garbage trash.
Press the button located on dust container “CYCLONE”, the
bottom of the container will open and the contents will fall out
to the trash.
7
After emptying the container, snap the bottom. Pay
attention to the fact that a seal located on the bottom of
container must be correctly positioned.
Container must be precisely closed. Otherwise
the dust will penetrate the vacuum cleaner
chamber and the suction power will decrease.
8
Insert the empty dust container “CYCLONE” to vacuum
cleaner. The characteristic “click” indicates that container
has been mounted correctly.
Emptying the dust container “CYCLONE” is necessary when
you notice that:
a) “CYCLONE” dust container full indicator indices turned on,
b) sucking power of vacuum cleaner decreased,
c) dust container “CYCLONE” is full.
C