Zelmer zvc231, Manual

Page: 41 / 44

47
ZVC231-001_v01
Your vacuum cleaner is equipped with
safety valve located inside the vacuum’s
compartment. It opens automatically, when the
suction hose or any of the elements attached
to it get choked or “CYCLONE” dust container
is overfull. Once the valve opens, you will hear
a distinctive “whirring” sound coming out of
the machine.
1
Switch the vacuum off by pressing ON/OFF button (5) .
2 Remove the plug from the power outlet.
3 Turn the suction tube end counterclockwise and remove
it from the inlet opening.
4 Disconnect “CYCLONE” dust container from the
vacuum. In order to do it, press the dust container clip and
swerve it away by holding the handle in the upper lid of the
dust container.
5 Move “CYCLONE” over the dust bin and press the clip
on the bottom lid and empty the container.
Now you should check EPA E10 basic filter and
if necessary, clean or replace it.
6 Close the bottom lid of the “CYCLONE” dust container
until you hear the click.
“CYCLONE” must be tightly closed. Otherwise,
the suction power may be reduced.
7 Attach the emptied “CYCLONE” dust container to the
vacuum until you hear the click.
It is necessary to empty “CYCLONE” dust container when you
notice that:
a) your vacuum cleaner is vacuuming less effectively,
b) dust container is full.
Filter disassembly
Your vacuum cleaner comes with “CYCLONE” dust container
with cyclone filtration enabling you to vacuum without the
need to use traditional bag. Characteristically, cyclone filter
uses the phenomena of the spinning stream of air in order
to separate solid contaminants. Contaminants are separated
in the circular part of the container, where the spinning air
throws them at the container’s wall; later they are moved
to the container’s next chamber. Pre-cleaned air is directed
to EPA E10 filter that picks up and holds the finest dust
fractions. This washable EPA E10 filter has been fitted with
a special filtering material to enable rinsing the dirt under
running water and reusing the filter.
The vacuum’s outlet is fitted with “Microfilter” outlet filter.
In case both filters: EPA E10 basic filter (12)
and “Microfilter” (11) get dirty, you can replace
them with the new ones, clean or rinse them
under running water.
You may not wash your filters in the washing
machine or dishwasher.
Filters may be dried only naturally.
You may not blow dry your filters or place it on
the heaters or radiators.
Before you replace the filters, make sure
the vacuum is switched off and the plug is
removed from the power outlet.
EPA E10 BASIC FILTER
It is necessary to clean EPA E10 basic filter from the fine
dust fractions.
Dismantle “CYCLONE” dust container according to item
C
.
1 Turn the upper lid of “CYCLONE” container to position
open and remove the lid. If the container is full, empty it
in accordance with item C .
2 Undo EPA E10 filter, removing it from the upper lid of
“CYCLONE” towards “ ” (the symbol and the direction
marked by an arrow are located next to the basic filter EPA
E10 handle).
3
Remove the shield from the filter.
4 Clean, wipe and dry the shield thoroughly.
●
Clean the basic filter’s belts (12) , if your filter is damaged,
you must replace it with a new one. If EPA E10 (12) has
been soiled, you may replace it with a new one, clean or
rinse it under running water. Remember to dry the filter
before you reattach it.
For safety reasons, attaching damp or
damaged EPA E10 filter (12) is not acceptable.
5 Insert the cleaned shield into the new/rinsed EPA E10 filter.
Make sure the slides on the protective flange are fitted into
the slots on filter hosing.
6 Reattach EPA E10 basic filter to its previous position in the
upper lid of the dust container (symbol “ ” along with the
direction marked by an arrow is provided next to EPA E10
handle.
7 Place the upper lid back over “CYCLONE” dust container
and turn it to the position closed .
8 Attach “CYCLONE” container to the vacuum until you
hear the click.
It is recommended to replace EPA E10 basic
filter (12) every 6 months of operation.
Damaged EPA E10 filter should always be
replaced with a factory new and original item.
“MICROFILTER” OUTLET FILTER
1
In order to replace “Microfilter” (11) press the filter cover
interlock and remove the outlet filter cover.
2 Remove the filter from the cover.
D
E