36
MM2000-001_v04
Technical data
The technical parameters are given on the rating plate of the
product.
Maximum time of non-stop operation:
15 minutes
An interval between repeated operation:
30 minutes
Noise level (L
WA
):
76 dB(A)
The appliance is 1st class device equipped with a connecting
cord with a protective conductor and a plug with an earth pin.
Always plug the appliance to the grounded electrical outlet.
ZELMER mincers meet the requirements of the applicable
standards.
The appliance complies with the requirements of the
following directives:
–
Electrical equipment designed for use within specific
voltage limits (LVD) – 2006/95/EC.
–
Electromagnetic Compatibility (EMC) – 2004/108/EC.
The product is marked with CE symbol on the rating plate.
Appliance description
The foodstuff mincer consists of:
1
Drive unit – each drive unit is designed to work with each
mincing unit and shredder manufactured by ZELMER.
There are ventilation openings in the rear cavity of the
drive unit compartment.
1a
On/Off button
1b
„Reverse” switch
1c
Lock button
Mincer unit consisting of:
2
Mincer body
3
Feed screw with attached coupling
4
Double-side cutter
5
Screen with 4 mm holes
6
Threaded ring
7
Tray
8
Pusher
Parts and accessories comprising:
9
Screen with 8 mm holes
10
Screen with 2.7 mm holes
11
Sausage stuffing tube
12
Insert
Mechanical safety device for the motor
13
Scroll
14
Coupling
15
Screw M5x20
The mincer is equipped with mechanical protection, which
secures the motor against damage – the teeth of the scroll
coupling will break when the mincer is overloaded (e.g., when
bones have entered inside the mincer body).
Replace the broken coupling with the new one:
A
A
●
unscrew the screw
(15)
in the scroll
(13)
with the broken
coupling,
●
remove the broken coupling
(14)
,
●
fit the new coupling
(14)
and tighten it with the screw
(15)
.
„Reverse” function
The motor has a special function allowing to temporarily
change the direction of the scroll. It is used if mincing is
limited and/or if there is too much product in the mincer body
(the scroll does not take the product). Press the
„
R”
switch
for a short period of time, the product will be removed from
the inside of the mincer body. Press the
„I”
button once
again to continue operation.
If the scroll is still blocked by the excess of product, use the
„R”
switch once again, remove the product from the mincer
body and next remove product parts which make it difficult to
mince (e.g. sinews, etc.).
In some cases it is necessary to dismantle the mincer body
and remove the above-mentioned obstacles.
Working with the mincer unit
Insert the following parts into the mincer body
(2)
:
1
Insert the scroll
(3)
with the coupling
(14)
facing inside.
2
Fit the knife
(4)
onto the pin of the scroll
(3)
.
3
Place the screen
(e.g. 5)
over the knife so that the
protrusion in the mincer body will fit into the groove in the
circumference of the screen.
4
Tightly fit all the elements of the mincer unit.
5
Fit the assembled mincer unit onto the drive unit
(1)
and
turn it until you hear a click of the lock.
6
Place the tray
(7)
on the mincer body
(2)
.
Preparing the mincer for operation
and starting the mincer
1
Place the drive unit
(1)
near the mains socket on a hard,
stable surface. Do not obstruct the ventilation openings in
the housing.
●
Wash all parts and accessories before the first use.
●
Assemble all the required parts and attach them to the
drive unit.
2
Carefully pull out the power cord, and then insert the
plug in the mains socket.
3
Start the mincer by means of the switch button
(1a)
.
Use only the pusher (8) to push products.
Working with the sausage stuffing tube
Insert the following parts into the mincer body
(2)
:
1
Insert the scroll
(3)
with the coupling
(14)
facing inside.
2
Fit the insert
(12)
onto the pin of the scroll
(3)
.
3
Fit the sausage stuffing tube
(11)
.
C
D
E