29
ZCP1000-001_v01
4
Unlock and remove the bowl
(2)
, by turning it counter-
clockwise.
●
Thoroughly wash the parts (except the motor unit) in
warm water with dishwashing liquid. After drying them
completely, start to assemble the cleaned elements.
For washing, use water at the temperature not
exceeding max. 60°C.
Preparing the juicer for operation
(assembly)
1
Place the bowl
(2)
on the motor unit
(1)
. Then rotate the
bowl clockwise with respect to the motor unit.
2
Put strainer
(3)
inside so that it is correctly seated on the
bowl
(2)
.
3
Replace the cone
(4)
on the strainer
(3)
.
Starting and operating the juicer
1
Prepare the fruit, cutting them in half.
2
Insert the power cord plug of the juicer into the mains socket.
3
Put the fruit flesh down on the cone
(4)
and gently press
to activate cone rotation and squeeze out juice.
To squeeze the juice out fully, the appliance
rotates the cone in the opposite direction
each time it is activated. Each time you press
the fruit, the cone will rotate in the opposite
direction.
Exercise care while pressing the fruit onto
the rotating cone and pay special attention to
fingers.
After finishing the juicing operation
1
Take out the power cord plug from the mains socket.
2
Unlock and remove the bowl
(2)
from the motor unit, and
then pour the juice into another container.
3
To store the juice in the bowl
(2)
cover it with a lid
(5)
and
put in the refrigerator.
●
Start to disassemble the juicer (see section
“Preparing
the juicer for operation”
).
4
Assemble clean and dry elements. Put away the cord.
Cleaning and maintenance
●
Clean the juicer thoroughly after each use in order to
prevent the juice residue from drying up.
●
Clean the power base with a wet cloth sprinkled with
washing-up liquid.
In case of water or juice getting inside the
power base, unplug the juicer and have
it checked at the service centre.
C
D
E
SUGGESTION
Information on the product and
suggestions for its use
●
The appliance is intended for domestic use. In case
of using it for commercial purposes the warranty
conditions will change.
●
Unplug the appliance after you finish using it.
●
Do not use abrasive cleaning agents in the form
of emulsions, creams, pastes, etc. for cleaning the
appliance housing. They may remove graphical
symbols, such as scales, markings, warning signs, etc.
●
Do not place the appliance on a wet surface.
●
Do not immerse the appliance power base in water
and do not wash it under running water.
●
Always place the appliance on a stable, even and flat
surface; the power cord may not hang over the edge
of the surface on which the appliance is placed.
●
The appliance is designed for use only in households
located up to 2000 m above sea level.
Technical data
The technical parameters are given on the rating plate of the
product.
Maximum time of non-stop operation: 15 seconds.
An interval between repeated operation: 15 seconds,
35 minutes – after 10 cycles.
Noise level (L
WA
): <80 dB(A).
Appliance structure
1
Juicer power base
a
Drive shaft
b
Power cord storage compartment
C
Power cord
2
Bowl
3
Strainer
4
Cone
5
Cover
Preparing the juicer for operation
(disassembly)
Before the first use, disassemble the juicer
and wash all the parts having contact with the
processed product.
1
Place the juicer near a mains socket on a hard, clean
and dry surface.
2
Remove the cover
(5)
.
3
Remove the strainer
(3)
and the cone
(4)
.
A
B
Summary of Contents for ZCP1000W
