Zelmer Eco Power VC3100, User Manual

Page: 62 / 66

66
VC3100-001_v01
When drawing out the power cable you have to
pay attention to yellow band indicating the end
of the cable drawn out. Further attempts (jerks)
may lead to damage of the cable.
7
Plug the cord into an AC outlet.
Before you start vacuum cleaner make sure whether the dust
container “CYCLONE” is mounted in chamber of the vacuum
cleaner, and whether the inlet and outlet filters are mounted
in the vacuum cleaner.
8 Start the vacuum cleaner by pressing On/Off button (4) .
9 Vacuum cleaner is equipped with electronic power
regulator, which - during the vacuuming - can smooth control
the suction power of vacuum cleaner. By turning the knob
(4) right or left – you can increase or decrease the suction
power.
10 Vacuum cleaner is also equipped in mechanical control
of suction power (9) , which is located on the handle of the
hose. It can temporarily slightly adjust the suction power,
without adjustment done with knob (4) .
Disassembly/assembly of “CYCLONE”
dust container
Vacuum cleaner is equipped in removable dust container
“CYCLONE” (which is a removable segment of vacuum
cleaner), which accumulates contaminants. As soon as the
“CYCLONE” dust container is full, it should be emptied.
Vacuum cleaner is equipped with a safety
valve which is located in the chamber of the
“CYCLONE” dust container. The valve is
activated (open) automatically when a total
jam (occlusion) occurs on the sucking hose
or this happens to equipment connected to it,
as well as in the case of excessive overfill of
“CYCLONE” dust container. When the valve
is open you can hear a characteristic sound
(“a sound of flutter”) in the vacuum cleaner.
1
Vacuum cleaner is equipped with a dust container
“CYCLONE” full indicator (5) . When the gap of dust container
“CYCLONE” full indicator is totally filled with red mark during
operation (vacuum cleaner operates at full power and
sucker nozzle or brush is upraised over cleaned surface)
so this informs that there is a need to empty the dust bin
“CYCLONE”. The dust container “CYCLONE” full indicator
(5) may work also in the case of clogging of the suction hose
or clogging of equipment connected to the hose.
2
Switch off the vacuum cleaner by pressing On/Off
button (4) .
3 Take off the cable connection plug from the wall outlet.
4 Press the two side buttons on the hose end , then remove
the hose end from vacuum cleaner inlet hole.
5 Raise the hook to unlock the dust container “CYCLONE”
(7) and remove dust container “CYCLONE” (16) from the
vacuum cleaner.
C
6 Move the dust container “CYCLONE” on garbage trash.
Press the button located on dust container “CYCLONE”, the
bottom of the container will open and the contents will fall out
to the trash.
7
After emptying the container, snap the bottom. Pay
attention to the fact that a seal located on the bottom of
container must be correctly positioned.
Container must be precisely closed. Otherwise
the dust will penetrate the vacuum cleaner
chamber and the suction power will decrease.
8
Insert the empty dust container “CYCLONE” to vacuum
cleaner. The characteristic “click” indicates that container
has been mounted correctly.
Emptying the dust container “CYCLONE” is necessary when
you notice that:
a) “CYCLONE” dust container full indicator indices turned on,
b) sucking power of vacuum cleaner decreased,
c) dust container “CYCLONE” is full.
Disassembly of filters
In case of dirty filters: inlet filter, foam filter
(15), HEPA inlet filter (14), outlet foam filter (13),
“Microfilter” (12) you can replace them with
new filters, clean them or rinse with running
water.
Do not wash the filter in the washing machine
or dishwasher.
Filters can be dried in natural way only.
Do not dry the filters using hairdryers, on
heaters and radiators.
Before replacement of filters make sure that
vacuum cleaner is switched off and connection
cable plug is pulled out from the wall outlet.
INLET FILTER HEPA AND FOAM INLET FILTER
Vacuum cleaners are equipped with outlet filter HEPA (High
Efficiency Particulate Air) type H10 or H13.
These filters have exceptionally high filtration capacity, are
made of special fibers, which can retain almost all dust
particles. The filter standards H10 and H13 define the
permeability of the filter: H10 filter can retain 85% of particles
diameter of 0.3 microns, and H13 filter up to 99.95% of all
impurities.
It is necessary to clean periodically the inlet filter HEPA (14)
in order to remove minor fractions of the dust, and foam inlet
filter (15) must be also cleaned.
Disassembly the “CYCLONE” dust container and empty it in
accordance with paragraph (C) .
1
Remove the HEPA foam inlet filter (14) from “CYCLONE”
dust container
2 Remove foam inlet filter (15) . If the foam inlet filter (15)
is dirty, you can replace it with a new filter, you can clean
D