Zelmer 33Z011, User Manual

Page: 40 / 44

40
GW33-017_v02
How to use
IONIC CONDITIONING
Ionic conditioning switches on automatically when the hair
dryer is switched on. The control lamp (3) will light up.
Negative ions are generated which reduce the gathering of
electric charges on hair. They also allow hair to absorb more
moisture thanks to which hair is softer and more shiny.
OPERATION
The selected operation options are indicated by the six
colored control lamps on the appliance’s housing:
1 Press and hold the ON/OFF button (5) for two seconds
to switch on the hair dryer. Press and hold the button again
to switch off the appliance.
The control lamp
●
(3) is green which indicates that the
ionic function is active.
The blue control lamp lights up when cold shot is on.
●
Yellow control lamp – indicates warm airflow.
●
Bright orange control lamp – indicates the first heat
●
intensity level.
Dark orange control lamp – indicates the second heat
●
intensity level.
Red control lamp – hot airflow.
●
2
To adjust the heat intensity level press the «Heat +/−»
(6) buttons. To increase the heat intensity level press «+»
and to decrease it press «−». Appropriate control lamps will
light up.
3
To adjust the airflow speed press the «Speed +/−»
buttons (7) . To increase the airflow speed press «+» and to
decrease it press «−».
There are 4 airflow speed settings.
4 To switch on the cold shot function press (9) , the blue
control lamp will light up. Press again to resume hot airflow.
MEMORY FUNCTION
If the hair dryer operates for more than 1 minute the recently
set operation options that is the heat intensity level and the
airflow speed are remembered and shall be applied when
the appliance is switched on once again.
HAIR CARE
For best results wash hair, dry with a towel to remove excess
moisture and comb before blow drying and styling.
QUICK BLOW DRYING
Using the buttons (6) set the second heat intensity level (the
bright orange and the dark orange control lamps will light
up), using the buttons (7) select the desired airflow speed
and dry hair. Remove excess moisture from hair with hand or
towel and continue to blow dry.
STRAIGHTENING
Using the buttons (6) set the second heat intensity level
(the dark orange control lamp will light up) or the fourth heat
intensity level (the red control lamp will light up), using the
buttons (7) select the desired airflow speed and dry hair.
When hair is almost dry attach the concentrator (1a) to the
end of the nozzle and lower the heat intensity level using the
buttons (6) . If necessary change the airflow speed as well (7) .
Divide hair into sections and layers. Use a round or paddle
brush to run down the length of the hair and simultaneously
run the stream of hot air from the dryer. Slowly straighten
each section from top to bottom. Repeat with all layers of
hair.
NATURALLY CURLY HAIR
Using the buttons (6) set the first or second heat intensity
level (the bright orange and the dark orange control lamps
will light up), using the buttons (7) select the second or third
airflow speed. Twirl strands of hair around your fingers, turn
them in the direction of the natural curl and dry directing the
airflow between fingers. After receiving the desired result
press the cold shot button (9) (the blue control lamp will light
up) to set the style.
LIFTING AND ADDING VOLUME
Select the desired heat intensity level (1-4), select the
second, third or fourth airflow speed. Dry hair at the roots
starting from the back of your head. Divide hair into strands
and direct the airflow up the shaft. This will lift the hair at the
roots and add volume to your hair style. You can also use the
diffuser (1b) to achieve such results.
STYLING HAIR
Using the buttons (6) set the warm airflow (the yellow control
lamp will light up) or the first heat intensity level (the bright
orange control lamp will light up), using the buttons (7) set
the first or second airflow speed, attach the concentrator (1a)
to the end of the nozzle. Divide hair into strands and style
using a brush. While styling, direct the airflow at hair in the
desired direction. If necessary direct the airflow at each hair
strand for 2-5 seconds to set style. The time required is to be
chosen individually and depends on the hair type.
THE COLD SHOT FUNCTION
This model is equipped with a cold shot function which is
used to set style. Press the cold shot button (9) (the blue
control lamp will light up). This will enable to set the desired
hair style. To switch off the cold shot press the button (9)
once again. The blue control lamp will go out.
Cleaning and maintenance
The hair dryer is intended for household use only.
●
Always switch off the hair dryer using the button
●
(5) and
unplug the appliance.
We recommend to take off the air inlet grill
●
(4) every
once in a while in order to clean it and to clean the filter
net underneath the air inlet grill.
Take off the air inlet grill by simultaneously pressing the
●
grill release buttons (4) and carefully pulling it towards
yourself. Clean the grill using a brush, clean the filter net
located underneath the grill and replace the air inlet grill.
The housing can be wiped with a damp cloth, however it
●
needs to be wiped dry afterwards.