54
WATER CONTAINER PROTECTION
This appliance is equipped with an internal water contain
-
er
(D)
which is fastened with a band to protect the water
lever switch during transportation. Before the initial use,
remove the water container from the appliance and re
-
move the band (see picture below). Gently replace the
water container back to its original position. Do not press
the water container, it may cause the failure of the appli
-
ance.
When the water in the water container reaches a prede
-
termined level, the display will show “P1: and the water
full indicator will start to flash (red). Gently remove the
water container and dispose of the water (see picture
below). Replace the water container back to its original
position. The red light will stop flashing and the “P1” sym
-
bol will disappear. The appliance will continue to operate
properly.
Note: Remove the water container slowly to prevent water from splashing. The water full indicator will begin to flash and the display
will show the symbol “P1” when the water container is removed / displaced or when the predetermined water level is reached.
CLEANING AND MAINTENANCE
1. Unplug the appliance before cleaning.
2. Do not use abrasive detergents such as emulsions, cream cleaners, polishes, etc. to
clean the housing. They may remove the graphic information symbols.
3. Wipe the housing with a damp cloth. Do not wash the appliance directly under a tap or
using a water hose. Electric shock risk.
4. If the air filter is blocked with a large amount of dust, the air flow volume will be re
-
duced. Clean the air filter every two weeks.
Opening and cleaning the air filter
1. Remove the filter cover and take out the air filter.
2. Wash the air filter by immersing it gently in warm water (about 40°C) with a neutral de
-
tergent. Rinse the filter and dry in a shady place.
3. Attach the filter to the filter cover using the attachment hooks on the inner surface of the
cover.
4. Put the filer cover back to the appliance.
Power cord and plug
Pull the projection to open the power cord compartment.
Keep the power cord and plug clean. Roll up the power cord and store it in the power com
-
partment if the appliance is not used for a long time.
BEFORE THE START OF THE SEASON
1. Check if the air inlets and outlets are not blocked.
2. Make sure the air filter is properly installed before operating the air conditioner. If the
air filter removed, dust and foreign objects may result in faulty performance of the appli
-
ance.
BEFORE THE END OF THE SEASON
1. Switch off and unplug the air conditioner.
2. Clean the air filter and other parts.
3. Remove the water container. Beside the continuous drain hose you will find a section of
hose that is plugged at the end. Remove the plug from the hose. Water from the bottom
tray will be removed through the drain hose.
4. Cover the appliance to protect it from dust and dirt.
Band
Remove
the drain plug
Hose
Band
Power cord
compartment
Summary of Contents for 23Z010
