background image

5

1. Getting started with BIKE all in one

1.1 Intended use

BIKE all in one

 is intended to be used exclusively within the bike which was sold with.  Any 

attempt to mount 

BIKE all in one

 on another bike will void warranty claims. 

BIKE all in one

 is not permitted for competition and race use.

1.2 Initial operation

BIKE all in one

 can only be activated when the battery state of charge is sufficient. In 

order to check the battery state of charge of your 

BIKE all in one

 please refer to 4.1.

1.3 Turning on the system

BIKE all in one

 turns on automatically when the rear wheel reaches a speed higher than 

5 km/h.  Thus, to turn on 

BIKE all in one

 just start pedaling your bike as usual or spin the 

wheel while you lift the bike, as explained in Figure 1 .

1.4 Turning off the system

BIKE all in one

 automatically turns off when no activities are detected within 2 minutes, in 

order to reduce the idle battery use. 

I

2

3

Figure 1: in order to turn on BIKE all in one, lift the bike (1), push the pedal 

(2) such that the rear wheel spins fast (3).

Summary of Contents for BIKE all in one







































Reviews: