Zehnder Rittling ComfoAir 155 WM Installation Instructions Manual Download Page 18

Page: 18 / 20

3.1.10

Recommissioning Menu Structure

Port Configuration

Input password 1010 to proceed into Setup Menu screens

Rotate button to choose either RH (Right Hand) or LH (Left Hand) Configuration

Password

Extract High

Wizard airflow setting will be shown . . . rotate button to required airflow %

Supply High

Wizard airflow setting will be shown . . . rotate button to required airflow %

Extract Low

Wizard airflow setting will be shown . . . rotate button to required airflow %

Supply Low

Wizard airflow setting will be shown . . . rotate button to required airflow %

Humidismart

Rotate button to choose either ON or OFF (Default setting: ON)

Timersmart

Rotate button to choose either ON or OFF (Default setting: ON)

Setup Menu

Service Menu

User Menu

Recommissioning

See Homeowner Guide

Comfort Temp

Rotate button choose between 21ºC - 28ºC (Default setting: 22ºC)

EXIT

Rotate button to EXIT and press button to select

Extract AUX

variable option 15% - 100%

Supply AUX

variable option 15% - 100%

Summary of Contents for ComfoAir 155 WM





















Search results

Summary of Contents for ComfoAir 155 WM

Reviews:

Related manuals for ComfoAir 155 WM

Brands by name

Popular brands

Zehnder Rittling ComfoAir 155 WM, Installation Instructions Manual

Search results

Summary of Contents for ComfoAir 155 WM

Reviews:

Related manuals for ComfoAir 155 WM

Brands by name

Popular brands