background image

4

1.Instruction for the User

HOB BURNERS CONTROL KNOBS

The hob burners control knobs are situated on the hob

lateral panel. The symbols on the knobs mean that :

l

there is no gas supply
there is maximum gas supply
there is minimum gas supply

LIGHTING THE BURNERS
• For easier lighting, proceed before putting a pan

on the pan support.

To light a burner, push in the relevant control knob and

turn it anti-clockwise to "maximum" position.

Upon ignition, keep the knob pushed down for about 5

seconds. This will allow the "thermocouple" (Fig. 1 lett.

D) to be heated and the safety device to be switched

off, otherwise the gas supply would be interrupted.

Then,  check  the  flame  is  regular  and  adjust  it  as

required.

If  you  cannot  light  the  flame  even  after  several

attempts,  check  the  "cap"  (Fig.  1  lett.  A)  and  the

"crown" (Fig. 1 lett. B) are in the correct position.

To put the flame out, turn the knob to the symbol 

l

.

• Always turn the flame down or put it out before

taking the pans off the burner.

USING THE HOB CORRECTLY

To  ensure  maximum  burner  efficiency,  it  is  strongly

recommended that you use only pots and pans with a flat

bottom fitting the size of the burner used, so that flame will

not spread beyond the bottom of the vessel (see the table

beside).

It is also advisable, as soon as a liquid starts boiling, to

turn down the flame so that it will barely keep the liquid

simmering.

Carefully supervise cookings with 

fats or oil

, since

these types of foodstuff can result in a fire, if over-
heated.

Burner

minimum

maximum

diameter

diameter

Big (rapid)

180 mm.

260 mm.

Medium (semirapid)

120 mm.

220 mm.

Small (Auxiliary)

80 mm.

160 mm.

Fig. 1

Contents

FO 0204

1. Instruction for the User ............

Pag.

4

2. Cleaning and Maintenance ......

Pag.

5

3.  Periodic Maintenance ...............

Pag.

5

4.  Maintenance -

    Technical assistance..................

Pag.

5

5. Technical Data...........................

Pag.

6

6. Instruction for the Installer ......

Pag.

6

7. Electrical Connection ...............

Pag.

7

8. Adaptation to different

types of gas................................

Pag.

8

9. Building In ..................................

Pag.

10

Summary of Contents for ZGF 647

















Reviews: