23
To select a different level proceed as
follows:
1. With the machine switched on, press "half load" and
"drying options" push buttons simultaneously for about 5
seconds. In the multi-display appears an L followed by a
number (e.g. L 4) which corresponds to the current level.
2. Press within 5 seconds the "drying options" push button
(no dry indicator light flashes) until the required level
appears in the multi-display. The level increases by 1 each
time the push button is pressed.
3. 5 seconds after the "drying options" push button has last
been pressed, the dishwasher memorises the level
selected and returns to the programme setting mode.
The setting will remain memorised after switching off the
dishwasher.
Filling with salt
Special salt can be added in one of two ways:
●
If you are using dishwasher detergent that already contains
salt, the detergent including the salt is placed in the
detergent compartment.
- In this case the water softener must be set to 0, to
ensure that the special salt is taken from the detergent
container only.
●
If you are using dishwasher detergent and salt separately,
the special salt is to be put into the salt container.
- In this case the water softener must be set between 1
and 9 (depending on the water hardness in your area) to
ensure that the special salt is taken from the detergent
container only.
Only use salt specifically designed for use in
dishwashers.
All other types of salt not specifically designed for use in
a dishwasher, especially table salt, will damage the water
softener.
Only fill with salt just before starting one of the washing
programmes (not the Rinse and hold programme).
This will prevent any grains of salt or salty water, which
may have been spilt, remaining on the bottom of the
machine for any period of time, which may cause
corrosion.
To fill:
1. Open the door, remove the lower basket and unscrew the
cap of the salt container.
2. Pour 1 litre of water inside the container (this is necessary
only before filling with
salt for the first time).
3. Using the funnel provided,
pour in the salt until the
container is full.
4. Replace the cap making
sure that there is no trace
of salt on the screw thread
or on the gasket.
5. Screw on the cap tightly.
The salt container will require topping up periodically. You are
reminded of this by the salt indicator light on the control panel
which comes on when the salt has finished.
In case salt refilling is necessary, during the run of the
programme the salt indicator light will remain off. Only with the
door open and the machine switched on it will illuminate.
The salt indicator light on the control panel can remain
illuminated for 2-6 hours after the salt has been
replenished, assuming the dishwasher remains switched
on. If you are using salts that take longer to dissolve then
this can take longer. The function of the machine is not
affected.
Do not worry if water over flows from the unit when filling with
salt, this is quite normal.
Rinse aid
Rinse aid is automatically added during the last rinse, ensuring
thorough rinsing, and spot and streak free drying. The
dispenser, which is positioned inside the door, holds about 110
ml of rinse aid, which is sufficient for 16 - 40 dishwashing
programmes, depending upon the dosage setting.
Rinse aid can be added in one of two ways:
●
If you are using dishwasher detergent that already contains
rinse aid, the detergent including the rinse aid is placed in
the detergent compartment.
- In this case the rinse aid compartment must be empty.
If in the rinse aid dispenser there is still rinse aid you
must wait until it has finished before using detergent that
contains rinse aid. In this case the rinse aid indicator light
on the control panel will always remain illuminated.
●
If you are using dishwasher detergent and rinse aid
separately, the rinse aid is to be put into the rinse aid
dispenser.
- In this case the rinse aid dosage must be set in position
from 1 to 6 (see "Adjusting the dose") and the rinse aid
indicator light activated.
Filling with rinse aid
1. Open the container by turning the lid (A) anticlockwise.
2. Add the rinse aid until the container is completely full. The
indicator (B) will be completely dark.
3. Top up with rinse aid when the rinse aid indicator light on
the control panel illuminates.
Ensure that the lid is closed after every refill.
Clean up any rinse aid spilt during filling with an absorbent
cloth to avoid excess foaming during the next wash.
Use only branded rinse aid for dishwashers. Never fill the rinse
aid dispenser with any other substances (e.g. dishwasher
cleaning agent, liquid detergent). This would damage the
appliance.
SALE
SAL
T
SALZ
SEL
SR14
BR01
BR03
SO442
All manuals and user guides at all-guides.com
all-guides.com
