29
In this fully integrated appliance, the controls are located on
the top of the door. When selecting a programme, the door
needs to be slightly open.
1. Check that the baskets have been
loaded correctly and that the spray
arms can rotate freely
2. Turn on the water tap
3. Press the On/Off push button
The multidisplay will show the last selected programme
and the indicator lights of options previously selected will
illuminate.
If salt or rinse aid refilling is necessary, the corresponding
indicator lights will illuminate.
4a. Setting and starting the programme
without "delay start"
Press the "programme selection" push button until the
required programme number appears in the multidisplay
(see "Washing programmes" chart).
If programme 2 (intensive 70°C) is selected, also the SID
indicator light will illuminate.
If you wish to see the duration of the programme just
selected, ONLY with door opened, press the "cancel"
push button.
Select if desired: "half load" (in the multidisplay the
duration of the programme will be adjusted) and/or
"drying options".
Close the door, the programme will start automatically an
and audible signal advises you of that.
Once the programme has started, the multidisplay will
show the running time.
4b. Setting and starting the programme
with "delay start"
Once a programme and required options (see point 4a)
have been selected to use "delay start" proceed as
follows:
Press the "delay start" push button, the multidisplay will
show "h 0". Press the push button again to select the
number of hours you wish to delay the programme start
(up to a maximum of 12 hours).
If drying options and/or half load have been set the
corresponding indicators lights will turn off, but don’t
worry, the delay start will not modify the settings made
previously.
To set the time setting to zero press the "delay start"
push button until "h 0" appears in the multidisplay.
Close the door, the countdown starts automatically and
an audible signal advises you of that.
To see the progression of the countdown it is necessary
to open the door. The progression of the countdown is
confirmed by a flashing dot after the number in the
multidisplay.
The countdown will decrease from hour to hour.
The opening of the door will not stop the countdown.
(Remember to close the dishwasher door).
Once the delayed time has elapsed the programme
will start automatically. In the multidisplay will
appear the running time of the programme.
To cancel a delay start in progress, open the door and
press the cancel push button. the delay start will be
cancelled without modifying previous settings
(programme and options). In the multidisplay will appear
first "h 0" and then the number of the programme.
5. Interrupting/cancelling a washing
programme
Change or interrupt a washing programme in
progress ONLY if it’s absolutely necessary
To interrupt a washing programme
Attention! Hot steam may escape when the door is
opened. There is risk of scalding. Open the door
carefully.
●
Open the dishwasher door; the programme will stop.
Close the door; the programme will start from the
point in which it was interrupted.
●
Pressing the On/Off (in this case all the indicator
lights turn off). Press the On/Off push button again;
the programme will start from the point in which it was
interrupted.
To cancel a washing programme
Open the door and press the "cancel push" button.
An audible signal will inform you that the programme has
been cancelled and in the multidisplay will appear three
horizontal lines (---) for about 2 seconds and then the
number of the programme just cancelled.
The dishwasher has returned to setting mode and it is
now possible to select a new washing programme.
6. End of the washing programme
The dishwasher will automatically stop and an
intermittent audible signal will be heard when the
programme has ended. (When delay start has been
selected, the audible signal for end of programme is
automatically excluded).
In the multidisplay will appear three horizontal lines (---)
and all the indicator lights will turn off.
Hot steam may escape from the appliance when opening
the door immediately after the end of the programme,
therefore, open the door carefully.
Open the door and switch off the dishwasher by pressing
the On/Off push button or select a new washing
programme by pressing the "programme selection" push
button.
Unloading the dishwasher
Hot dishes are sensitive to knocks. The dishes should
therefore be allowed to cool down before removing from
the appliance.
Leave the dishes in the dishwasher for approx. 15
minutes, with the door ajar, after the end of programme
so that they dry better and will be cooler.
Empty the lower basket first and then the upper one; this
will avoid water dripping from the upper basket onto the
dishes in the lower one.
When the washing programme has finished, it is
recommended that the dishwasher is unplugged and the
water tap turned off.
Starting a washing programme
All manuals and user guides at all-guides.com
