background image

58

 

F

AUL

T FINDING F

AUL

T FINDING F

AUL

T FINDING F

AUL

T FINDING F

AUL

T FINDING

Installation and Servicing

SECTION 4 - FAULT FINDING

4.7  ‘F3’ - FAN FAULT

Does the wiring from the Fan to the PCB have 

secure connections at both ends and has not 

deteriorated?  Does the wiring have continuity?

YES

Rectify Wiring & 

connections

Is there 230Vac at the Blue and Brown connections 

to the 3 way connection on the Fan?

NO

Replace PCB

Replace Fan

NO

YES

4.8  ‘F4 OR L4’ - FLOW THERMISTOR FAULT

Disconnect the wiring from the Flow Thermistor

Check the resistance using a suitable multimeter connected 

across the Thermistor’s terminal pins.

  At 25 

o

C  expect 

9,700  - 10,300 

Ohms

  At 60 

o

C  expect 

2,400 -  2,600 

Ohms

  At 85 

o

C  expect 

1,000 -  1,100 

Ohms

Is the Thermistor value correct?

YES

Is the wiring securely connected to the low voltage 6 way 

connector at the front left hand side of the PCB?

YES

Replace PCB

Fit a new Thermistor

NO

Securely connect the wiring to the PCB

Is the wiring securely connected to the Flow Thermistor 

(located in the top of the Heat Exchanger?)

YES

NO

Securely connect the wiring to the Water 

Flow Thermistor

NO

4.9  ‘F5 OR L5’ - RETURN THERMISTOR FAULT

Remove the Return Thermistor from the CH Return 

Pipe and disconnect the wires.

Check the resistance using a suitable multimeter 

connected across the thermistor’s terminal pins.

  At 25 

o

C  expect 

9,700  - 10,300 

Ohms

  At 60 

o

C  expect 

2,400 -  2,600  Ohms

  At 85 

o

C  expect 

1,000 -  1,100  Ohms

Is the Thermistor value correct?

YES

Is there continuity between the PCB and the Thermistor?

YES

Replace PCB

Fit a new Thermistor

NO

Check and replace wiring as necessary

NO

Summary of Contents for ULTRA COMBI 30









































































Reviews: