Zanussi CZL 145 W, Instruction Booklet

Page: 14 / 20

7
TOO WARM
CCOO2
ZANUSSI
Cool Check Guide
The guide consists of a temperature sensitive strip
sealed in a shelf trim.
When the fridge is operating at the safe temperature
to store food the guide will appear black. If the
temperature rises above this level the guide will
show the words TOO WARM.
Positioning of the Cool Check
The shelf with the cool check temperature guide
must be placed in the fridge according to the
instructions located on the fridge wall and always
ensure the guide is at the front.
If the Cool Check shows TOO WARM
In certain conditions the temperature guide may
show TOO WARM if:
• The fridge is switched off
• The door has been recently opened
• A quantity of warmer food has been introduced to
the fridge
• The fridge temperature is above the
recommended maximum for the safe storage of
food.
The cool check will change to show “TOO WARM“
very quickly after the door has been opened. It will
however take a number of hours to return to black,
indicating that the temperature is correct.
The appliance should be left overnight and the cool
check examined in the morning. If the cool check
shows TOO WARM, turn the thermostat to a colder
setting leave overnight and examine again the
following morning.
Hints and Tips
• The guide is only suitable for use in the model
supplied.
• The guide will not operate in a freezer
compartment.
• When cleaning the shelf take care not to immerse
in water, and wipe away any spills.
INSTALLATION
Positioning
This appliance should only be installed at a location
where the ambient temperature corresponds to the
climate classification indicated on the rating plate, which
is located at the left on the inside of the appliance.
The following table shows which ambient temperature is
correct for each climate classification:
SN +10°C to + 32°C
N +16°C to + 32°C
ST +18°C to + 38°C
T +18°C to + 43°C
It should be located in a dry atmosphere, out of direct
sunlight and away from extreme temperature e.g. not
next to a boiler or radiator, or in a very cold room e.g. an
outhouse, where the temperatures may fall below 10°C
(50°F). If these temperatures are exceeded i.e. colder or
warmer, then the appliance may not operate correctly.
You should also ensure that air can circulate freely
around the back and the top of the cabinet. There must
also be at least 100 mm (4”) distance between the top of
the cabinet and any overhanging kitchen furniture (A).
Ideally, the appliance should not be positioned beneath
overhanging furniture (B).
There should also be a gap of 25 mm either side of the
appliance. Do not obstruct the space underneath. The
back of the cabinet may be placed close to the wall but
must not touch it. DO NOT install in places with
restricted ventilation.
Adjust the level of the appliance by screwing out the
adjustable foot, or feet, at the bottom of the cabinet
using your fingers.
D200
100 mm
10 mm 10 mm
A
B
NP007
Important
IF YOU ARE DISCARDING AN OLD APPLIANCE THAT
HAS A LOCK OR CATCH ON THE DOOR, YOU MUST
ENSURE THAT IT IS MADE UNUSABLE TO PREVENT
YOUNG CHILDREN BEING TRAPPED INSIDE.
Depending upon the position which you choose for your
appliance, you may wish to reverse the way in which
the door opens. To do this, refer to instructions on “Door
reversal”.
Please ensure that when the appliance is installed it
is easily accessible for the engineer in the event of
a breakdown.
Rear spacers
The plastic bag containing all relevant
documentation also contains two spacers to be fitted
into special holes in the back of the appliance.
Fit the spacers into the holes, taking care to ensure
that the arrow (A) is positioned as shown in the
diagram. Then turn them through 45° (arrow (A)
vertical) until they lock into place.
PR60
A
45
°
14
Important
It must be possible to disconnect the appliance from
the mains power supply; the plug must therefore be
easily accessible after installation.